Lynn Patrick
Well-known Member
Will the swinging drawbar kit (Part No: 49A34R) from an NAA/600/8N fit an early 960? If not, will any other model fit?
Thanks![/url]
Thanks![/url]
- Thread starter Lynn Patrick
- Start date
Lynn Patrick
Well-known Member
Thanks Dean. I realize the drawbar has a deeper drop, my first concern was if the belly mount & hanger will fit.
The under differential bracket will not have the pins for the row crop specific sway bars.
The drawbar hanger from a 6** series tractor will bolt on. Not sure about the bracket for a 8** series as the 7/9 series tractors use the 6** size differential rather than the larger 8** differential.
I would look for a salvage row crop in a salvage yard for the correct brackets. Should be easy to find.
Dean
The drawbar hanger from a 6** series tractor will bolt on. Not sure about the bracket for a 8** series as the 7/9 series tractors use the 6** size differential rather than the larger 8** differential.
I would look for a salvage row crop in a salvage yard for the correct brackets. Should be easy to find.
Dean
the early swinging drawbar system on the 900 looked like this. (I know the bar is upside down cause it's one off my 8n, but it worked) I also have the other style on my
950. Basically used a 600 rear so the one off a 600 and I believe the earlier models will work also.
As stated, the drawbar had two pieces that hung down to connect the inside swaybars.
BTW, if you're going to pull with it the standard drawbar, for height, is better than the drop bar.
Kirk
950. Basically used a 600 rear so the one off a 600 and I believe the earlier models will work also.
As stated, the drawbar had two pieces that hung down to connect the inside swaybars.
BTW, if you're going to pull with it the standard drawbar, for height, is better than the drop bar.
Kirk
Lynn Patrick
Well-known Member
Thanks to all for your comments! My '57 960 has the swinging drawbar like I want, my '55 has one like Kirk's picture & I want to replace it. I haven't been able to find a 9xx around here that still has a drawbar - they are all gone already. I did find one on a 600 but I put that one on my Jube as it also had the one like Kirk's. The belly bracket should be easier to find, & I may have to fabricate my own drawbar.
By the way, the 8xx support bracket is different. I have one of those & may be willing to work a trade if someone is interested???
By the way, the 8xx support bracket is different. I have one of those & may be willing to work a trade if someone is interested???
Similar threads
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy