|
| |
| Ford Tractors Discussion Forum |
Topic: 660 lift controls.
[Return to Forum]
| Author |
[Modern View]
|
| Robert NC
02-22-2013 16:11:09
98.17.99.48
|
Bit the bullet and pulled the lift top to replace the seals on the lift cylider. The lift lift control shaft coming through the lift cover has slop between the shaft and the lever that fits on it inside the cover. I have another shaft and lever from a 660. Can I change shaft and levers and not have to worry about resetting all the clearance. Hope I am making sense.Thanks in advance
|
|
|
| Robert NC
02-23-2013 17:47:43
98.17.99.48
|
|
Re: 660 lift controls. in reply to Robert NC, 02-22-2013 16:11:09
|
|
| Is the pin available or should I just braze it and the file/grind it round and smooth?
|
|
|
| soundguy
02-22-2013 16:24:36
184.233.0.17
|
|
Re: 660 lift controls. in reply to Robert NC, 02-22-2013 16:11:09
|
|
| | ditto what dean said. lift cover kit is 15 $.. don't half arse the job.. do the cam pin and cam if needed ( braze / weld / grind ).. then repalce all orings and piston seal/washer.. readjust using alt method without nuday tools.. etc. be good another 50 ys after that.
|
|
|
| Dean
02-22-2013 16:20:46
152.216.3.5
|
|
Re: 660 lift controls. in reply to Robert NC, 02-22-2013 16:11:09
|
|
| | You need to replace the cam follower pin and readjust the draft and position control adjustments while the lift cover is off in any event. Dean
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
