(800) 853-2651
SHOP NOW

NAA 12 v solenoid

J

Johnsfolly

New User
Solenoid went on my NAA with a 12 volt conversion. Tractor is
presently negative ground. Old solenoid (3 post) looks like it
was triggered by going to ground through the safety starter
switch. Replacement (4 post) is triggered by providing 12 volts
to the "s" terminal and apparently grounds through the
housing. Did Napa sell me the wrong solenoid?
Thanks in advance.
John
 
Yes, you got the wrong one. Don't worry about the voltage of the solenoid. The 6V isolated solenoid will work fine on 12V. It might actually just be easier to get a 6V isolated solenoid from a NewHolland dealer than track the right one down in the NAPA system... What you need is an isolated coil type solenoid that uses 3 posts and is triggered by ground... as opposed to one that is 3 pole and triggered by line voltage.

If you wish you could use the one you have... just use a cube relay to control the solenoid with the relay wired hot and it's control finding it's ground in the push switch.

Rod
 
napa st 541 is a 12v 4 post. 1 small post to key power.. 1 small post to thumb switch

napa st53 is a 6c 3 terminal...

both work.. I personally like the 6v stuff.. :)
 
Thank you all very much. I found another relay in the garage. It had a positive and a negative "small" post. I ran a shunt from the heavy 12 volt lug to the positive trigger and connected the wire from the starter button to the negative side of the trigger. problem solved!
John
 
(quoted from post at 18:01:12 01/04/13) napa st 541 is a 12v 4 post. 1 small post to key power.. 1 small post to thumb switch
Click to expand...

The ST541 is 6 volt. The ST542 is the 12 volt version of the same solenoid.

tractor037.jpg
 
yeah, that's correct.

541 is 6.. 542 is 12.. both 4444 ...

i guess if i don't make any typo's life won't be fun anymore. :)
 
You must log in or register to reply here.

Similar threads

S
Ford 600 12 volt conversion
Replies
4
Views
678
JMOR
J
J
Dead starter?
Replies
6
Views
487
showcrop
showcrop
P
300 u 6 to 12 v conversion update problem
2
Replies
28
Views
912
Paul 300 U
P
F
601 wiring
2
Replies
33
Views
3K
JMOR
J
F
Big mistake, changing to 12 volts
Replies
18
Views
1K
Freddie2010
F
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top