(800) 853-2651
SHOP NOW

600 no Hydraulics

S

stanger

New User
Hello,

I have a 600 and was using the bush hog and when i was finished the 3pt hitch would not raise as if I lost all Hydraulics. Any ideas as where to start troubleshooting ? I will need a diagram if it is a pump.

thank you
steve
 
gradually die or all at once?

where to start?

1, check hydro oil at the dipstick.

if it has oil, then check to see if it will lift with no load.

if it will not lift with no load, check pump for prime at the top/front plug on the head.

if it has oil there, check under the seat on the option panel, with the plug in it.. check for oil there. ( if you have a remote there.. check to make sure you didn't kick it engaged ) if not engaged.. check to see if remotes work. if they do.. pump and relief are fine..

if oil there under the seat and no remotes, then pull cap on rear and look in for massive leaks from top.


if nothing apparrent... pull top cover for a looksee.

no sweat on the diagram.. your service and parts manual have them.

( what? no manual? shame on you! )

get one at the CNh parts site... free..e tc..

post back

soundguy
 
here.. holding your hand / doing yer research for ya...
a41358.jpg
 
Is the tachometer still working? The hydraulic pump is driven by a gear off of the engine, and the tachometer cable is driven off of a fitting on the hydraulic pump, so if the tach is still working then at least you know that the pump is spinning. If the tach stopped working at the same time that the hydraulics stopped working, then it may be the gears that drive the pump.
 
First thing to check is the fluid level. No fluid or very low can burn up a hyd pump and if that happens your talking big $$ to fix/replace it. As for diagrams you need to buy a manual like the Ford I-T FO-20
 
If you have a vane pump and are using 134 fluid you can lose lifting power in hot weather.The 600 was designed to use 80 or 90 gear oil.If the lift works when the fluid cools dump the 134 and buy 2 gallons of 80 or 90 mineral gear oil for 15.00.
 
You must log in or register to reply here.

Similar threads

B
600 Steering Issue
Replies
2
Views
285
Hemmjo
Hemmjo
M
Ford 4000 hydraulics
Replies
8
Views
703
MAJK
M
G
AMT 600
Replies
4
Views
245
Jim.ME
J
W
Questions on Jubilee hydraulics
4 5 6
Replies
117
Views
3K
JMOR
J
M
Bush Hog Freeman loader 3000 fit Ford 3600
Replies
3
Views
326
Eman85
E
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top