Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Ford Tractors Discussion Forum
Show Parts for Model:


Welcome Guest, Log in or Register
Author  [Modern View]
scott t in taylor

09-17-2012 10:21:52

Report to Moderator

rotor on ford 860 breaks in three pieces.Help

[Log in to Reply]   [No Email]

09-17-2012 14:49:11

Report to Moderator
 Re: rotor in reply to scott t in taylor, 09-17-2012 10:21:52  
Getting TISCO old stock rotors? Big problems with junk rotors a couple years back. no problems lately.

[Log in to Reply]  [No Email]

09-17-2012 11:52:15

Report to Moderator
 Re: rotor in reply to scott t in taylor, 09-17-2012 10:21:52  
As sound said and are you by chance buying the parts from the that sells parts from the land of almost right??? If your getting the almost right parts then that is where your going wrong. The rotor shaft clip in one of the most important parts in it by the way

[Log in to Reply]  [No Email]

09-17-2012 11:06:08

Report to Moderator
 Re: rotor in reply to scott t in taylor, 09-17-2012 10:21:52  
got the dust cap spacer on..

got the rotor clip and rotor seated correctly?

dizzy cap on straight and not cocked to the side?

[Log in to Reply]  [No Email]

09-17-2012 10:53:02

Report to Moderator
 Re: rotor in reply to scott t in taylor, 09-17-2012 10:21:52  
Do you know that there is a little, round spring clip that slides onto the shaft and holds the rotor in position? If not, find a manual or an old Ford farmer, and then get thee to the New Holland dealer or the Parts department on this site.

Good luck.


[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2018 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters