|
| |
Topic: Re: Ford 860 Hydraulics
[Return to Forum]
| Author |
[Modern View]
|
| Kurt-NEPA
07-20-2012 06:16:31
70.44.245.96
|
Your linkage looks OK in your picture, but its hard to tell if its worn. It seems to me that for the adjustment to be that far off, something has to be broken, bent, or missing.
Zane Sherman sells a nice manual on adjusting the hundred series top cover. He's a wealth of knowledge too. Might be worth contacting him.
Zane's web page
http://pwp.att.net/p/s/community.dll?ep=16&groupid=220626&ck=
|
|
|
|
| DaveDor
07-20-2012 10:47:52
69.174.149.172
|
|
Re: Ford 860 Hydraulics in reply to Kurt-NEPA, 07-20-2012 06:16:31
|
|
| DaveDor
07-24-2012 12:36:59
69.174.149.172
|
|
Re: Ford 860 Hydraulics in reply to DaveDor, 07-20-2012 10:47:52
|
|
| Haven't taken anything apart yet, but after a closer inspection I discovered the Clevis Pin in the Hydraulic Lift Hand Control Lever Assy is worn approx half way through. This is the pin which the Hydraulic Lift Ram Arm rides against.
Seems that this could put linkage way out of tolerance. Look at center of photo, almost a 1/3 of way up.
This post was edited by DaveDor at 12:56:25 07/24/12.
|
|
|
| DaveDor
08-03-2012 18:24:28
69.174.149.172
|
|
Re: Ford 860 Hydraulics in reply to DaveDor, 07-24-2012 12:36:59
|
|
| Clevis Pin replaced. Used a 1/4" grade 8 bolt cut to size. Also replaced another badly worn pin in the Draft Control Connecting Link.
Those two repairs brought the system back into specs so I could do the adjustments. Just need to reinstall the lift cover and check operation.
|
|
|
| DaveDor
08-04-2012 18:36:18
69.174.149.172
|
|
Re: Ford 860 Hydraulics in reply to DaveDor, 08-03-2012 18:24:28
|
|
| Cover installed and everything checks so far. Tomorrow will hook up the Three Bottom plow and give it a test. :D
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
