(800) 853-2651
SHOP NOW

Where to locate part

F

fireman176

Member
TO30 1951 model. The linkage that connects the governor broke where it threads into the part surrounded by compensating spring. I looked on YT parts page and could only find the spring. Any suggestions? The threaded rod broke off about an inch from end of rod and I might be able to find someone to weld it together but its not that big of a rod.
 
Its very hard to identify what specific part you need without a part number.
If you go to Agco parts books online and find the TO 30 parts book, and the specific part you need, get its part number, and let me know what it is...I may be able to help you out.
I had a look myself using your description and came up with part number 181567m1? If this is the correct part you need, it is still available from Agco. About $10.00.
However I am not sure if it is the one you need or not.
Check it out and get back to me. If the part you need is NOT available from Agco...Sometimes I can find it somewhere.
Wayne
 
(quoted from post at 17:16:58 06/12/15) Its very hard to identify what specific part you need without a part number.
If you go to Agco parts books online and find the TO 30 parts book, and the specific part you need, get its part number, and let me know what it is...I may be able to help you out.
I had a look myself using your description and came up with part number 181567m1? If this is the correct part you need, it is still available from Agco. About $10.00.
However I am not sure if it is the one you need or not.
Check it out and get back to me. If the part you need is NOT available from Agco...Sometimes I can find it somewhere.
Wayne
Click to expand...
his is exactly the part, thanks so much. I think I have learned I can remove the ball joint end off the broke shaft and just get a threaded rod that the ball joint will fit onto and make it work.
 
Is the part you require on this page? Taken from FERGUSON REPAIR PARTS LIST
FORM NO. 693 041 M2
Bob....
a193522.jpg
 
You must log in or register to reply here.

Similar threads

G
John Deere 40U - Governor linkage issues
Replies
6
Views
524
Glen D Anderson
G
C
Bush hog 3pt to Pull type conversion
Replies
18
Views
4K
BarnyardEngineering
BarnyardEngineering
A
Famall 706 diesel - 2 head bolts with spacers along exha
Replies
6
Views
510
rustred
rustred
A
I finally got to drive my 318 today
Replies
2
Views
584
T.R.K.
T
E
Identification of Linkage Rod and Where it Belongs
Replies
10
Views
1K
DrAllis
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top