Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Harry Ferguson Tractors Discussion Forum
Show Parts for Model:

Re: Long winter mower project- 2 many pics

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
Tony in Mass.

07-23-2013 19:39:59

Report to Moderator

JASON!!! How long would it take you to drive up here? Leave yesterday.
TO30, the bolts in the ... tranny to diff joint? are from the back forward into blind holes in the tranny half, these brackets weren't made to do that. Or they would be even further off. And no pairs of holes are the same center to center.
Can't focus that good, but the bars are 22&1/2" apart, the 35 is 23&1/2... the TO 30 is 28 inches!! The pto pulley is much newer, has the adapter in it, but the HF diff must stick out the stern a couple 3 inches more on the 35's, I was so put off I forgot to measure it on the 30. I don't know how badly someone reworked this, but nothing is even close. I am stumped. Email me your phone # if you want gory details...

[Log in to Reply]   [No Email]
Jason S.

07-24-2013 06:36:36

Report to Moderator
 Re: Long winter mower project- 2 many pics in reply to Tony in Mass., 07-23-2013 19:39:59  
Well Tony, I haven't driven anywhere in over a week. My old truck kind of tore up. It wasn't the trucks fault though. It's a 1978 Ford F150 short wheel base 4x4. I put a new fuel pump on it and the pump had 10lbs of pressure. Way too much for a carburetor so I ordered a Carter pump from Rock Auto and while I was waiting on it to come in I decided to fix a burnt exhaust valve. The motor was rebuilt by a previous owner but when he had the heads fixed they reused the original soft valves. So I put all new valves, springs, retainers,locks,timing set, cam and lifters while I was in there. I ground the valve seats myself with a black and decker valve seat grinding kit I bought on eBay a year ago. I've saved a lot of money that way. I should be finished hopefully tomorrow because I'm having to work in between the rain which it does every day here. With that being said, my best friend has an 8N and next time I go over there I will measure his and then measure my TO-20 and you can compare them to your TO-30. See you should have taken me up on that Dearborn mower Although I do have an extra Dearborn I have for parts, and an extra Ferguson A-EO-A20 mower. I may have to round up some mowers I have that I know fit on a TO-20,TO-30,TO-35 and trade you out of that FEO

[Log in to Reply]  [No Email]
Tony in Mass.

07-24-2013 09:02:48

Report to Moderator
 Re: Long winter mower project- 2 many pics in reply to Jason S., 07-24-2013 06:36:36  
That's what's changing my travel plans Jason, '88 dorF... campervan- fuel pump! An electrical gremlin, I took out the whole tank that was syphoning from the other etc etc. Got all that straightened out and back to basics... and now the wiring or ??? Is getting me disgusted. Gunshy? I don't want to be ... 'Found On the Road Dead' with a trailer full of priceless fergie mowing machines.... did I just say that? Must be the heat...

[Log in to Reply]  [No Email]
Jason S.

07-24-2013 18:56:48

Report to Moderator
 Re: Long winter mower project- 2 many pics in reply to Tony in Mass., 07-24-2013 09:02:48  
Hey Tony, you don"t need a Dearborn two bottom turning plow do you? I found one for $150.00 today, I don"t need it but I thought about getting it, throwing a little paint on it and reselling it. Most two bottoms around here go for $250.00 to $400.00.

[Log in to Reply]  [No Email]

07-24-2013 18:13:00

Report to Moderator
 Re: Long winter mower project- 2 many pics in reply to Tony in Mass., 07-24-2013 09:02:48  
Tony,Tony, Tony....FORD=Fix Or Repair Daily.... The van is just living up to it's good name! Hope you get it going for this Expo everyone is heading to! Sam

[Log in to Reply]  [No Email]
Jason S.

07-24-2013 12:10:56

Report to Moderator
 Re: Long winter mower project- 2 many pics in reply to Tony in Mass., 07-24-2013 09:02:48  
I hope you didn"t put an Airtex brand pump in it. They are garbage.

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2018 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters