Yesterday's Tractor Co. Compare our Prices For Parts
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Harry Ferguson Tractors Discussion Forum
Show Parts for Model:

Re: 85mm to 87mm kit source

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
Trac

03-25-2013 15:06:30
71.48.107.173



Report to Moderator

What year is it? it may all ready be the 87 bore. My tea is a 52 there should be rised numbers behind the carb. whitch tells the year the motor was made but i don"t know how to find that info.




[Log in to Reply]   [No Email]
shackwrrr

03-26-2013 09:12:34
98.22.213.51



Report to Moderator
 Re: 85mm to 87mm kit source in reply to Trac, 03-25-2013 15:06:30  
Ive found markings that say its a 51 but that is on the rear end housing, I think that may have been replaced at some time. The Hydraulic control fork inside has an aluminum bridge which wasn't supposed to be there until 53 and its 12v electronics with a lucas generator. Behind the carburetor the casting says 85, I dont recall a year on the engine casting.



[Log in to Reply]  [No Email]
Trac

03-26-2013 15:23:21
71.48.107.173



Report to Moderator
 Re: 85mm to 87mm kit source in reply to shackwrrr, 03-26-2013 09:12:34  
OK i'm not sure but on mine behind generator reads 26 6 2 so i'm guessing the block was cast the 26th day on the 6th month on the year of 1952 and acording to the serial numbers it is a 52. Only the early TEA's came with the smaller bore



[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters