(800) 853-2651
SHOP NOW

two stage clutch

S

s19438

Well-known Member
on a TO-35 is it possible to convert a one stage clutch to a two stage clutch?

is it simply a matter of splitting the tractor and dropping in the new clutch or are other modifications required?

thanks.
 
The two stage clutch conversion entails changing the input shafts at the front of the gearbox complete with the housing and bearings. this means pushing the bottom shaft either back (or pulling it forwards depending on the age of the tractor) to let the large gear drop down enough to let the replacement housing into place. You then need a dual clutch cover and the two plates. Some of the original covers can be built to suit the dual clutch configuration, but it is easier to replace the complete unit. It is do-able, but quite a bit of time and money involved unless you can find secondhand parts of good quality and use your own time.
Sam
 
Different Flywheel, different Transmission layout completely, only way to do it is get another Transmission, Flywheel and Clutch. Not really practical.You could get another Tractor with a Dual Clutch and if you want to keep your Engine then switch it into the new tractor. Not really practical...John(UK)
 
I have done this conversion using the original gearbox and flywheel, but as John has pointed out sometimes the flywheel is different.
Sam
 
As John and Sam say, it 'can' be done, but, to purchase all the bits and pieces from the rear main bearing to the PTO spline, it most likely would cost more than finding another tractor with a blown engine. Just lately I see people want $600 for a used clutch pack, and others asking $500 for a complete yet dead tractor. Putting the engine you like the least on the back half you like the least makes a nice tractor to sell to someone who just wants to haul firewood...
 
I've got a parts F-40 with good transmission--duel pressure plate, no clutch.Make offer. I'm in Texas. The PO had busted rock shaft and housing lifting big round bales hay. I used engine in HC F-40 I'm building.I drove tractor before removing engine.
 
You must log in or register to reply here.

Similar threads

C
Super Dexta 11" Single Stage Clutch Kit
Replies
5
Views
276
Majorman
Majorman
G
Ford 861 input shaft seals
Replies
6
Views
371
used red MN
U
K
Massey 135 heavy clutch pedal
Replies
8
Views
614
jtxn
J
I
John Deere 2020 PTO questions
Replies
3
Views
277
Jim.ME
J
D
Ford 3000 Clutch issues
2
Replies
20
Views
717
Btzj02
Btzj02
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top