1930 mccormick 22-36 carb

southcryn82 · May 28, 2015

could anyone recommend a shop to rebuild and clean up a IHC RW (brass carb) I've called several shops and they wont touch it due to it's age

Nebraska Cowman · May 28, 2015

I do my own. They are pretty simple.

southcryn82 · May 28, 2015

who would be best to order the parts from? float and gaskets etc.

Nebraska Cowman · May 28, 2015

Rice Equipment will have everything you need. If you don't see it on the web site give Frank a call.
Rice

southcryn82 · May 28, 2015

thank you

Nebraska Kirk · May 28, 2015

(quoted from post at 17:55:18 05/28/15) could anyone recommend a shop to rebuild and clean up a IHC RW (brass carb) I've called several shops and they wont touch it due to it's age

I rebuild my own as well. I can rebuild yours for you if you would like, but they are pretty simple. Beadblast everything and make sure all the little holes and passageways are clean, install a new float, needle & seat, and make new gaskets and you are good to go. I get new cork floats and needle & seat from Rice and make my own gaskets.

James Williams · May 29, 2015

There is only one gasket on a 10-20 carb,and that is the fuel screen bowl.

jimmy

SweetFeet · May 30, 2015

If the center suction stem is bad, I think Fordson House has them for the 15-30 carburetor. (YT doesn't have parts for a tractor that old).

We had to replace the suction stem in our carburetor on our Farmall Regular... also a brass snail shell style carburetor, only smaller sized. It was rusted out.

southcryn82 · Jun 1, 2015

If you would be willing to clean up and rebuild it I'd be more then happy to pay you carbs are not my strong point especially not a fragile brass one I'm not concerned with the water injection as this will be a show tractor and i'll never use it just need it to look alil better and work... Would you have any suggestions for repairs to my intake/exaust manifold my intake ports are in great shape but all my exaust ports are really rough and don't seal well at all and I know welding cast an milling is a tricky task I wasn't sure if doubling up the gaskets would maybe be an easy cure since there so thick.

LewissiweL · Sep 8, 2016

I rebuild my own as well. I can rebuild yours for you if you would like, but they are pretty simple. Beadblast everything and make sure all the little holes and passageways are clean, install a new float, needle & seat, and make new gaskets and you are good to go. I get new cork floats and needle & seat from Rice and make my own gaskets.
------------------------------------------------------------------------

Hello. I have A Brass international carburetor on A 22-36. May I enquire if I could kindly seek your service in rebuild/cleaning, as well as if possible A repair?. The carburetor in photo is not mine but exactly the same. On the bottom the dommed cap mut has been broken off I still have the cap nut but the tube or whatever it was attached to it be broken from. Your service if possible I would be most grateful for. I would be willing to pay up to $200. for your service or anyone here if they can assist me. Or what be necessary for services. Shipping to and from you the carburetor I will certainly pay.

Nebraska Kirk · Sep 9, 2016

(quoted from post at 19:26:29 09/08/16) I rebuild my own as well. I can rebuild yours for you if you would like, but they are pretty simple. Beadblast everything and make sure all the little holes and passageways are clean, install a new float, needle & seat, and make new gaskets and you are good to go. I get new cork floats and needle & seat from Rice and make my own gaskets.
------------------------------------------------------------------------

Hello. I have A Brass international carburetor on A 22-36. May I enquire if I could kindly seek your service in rebuild/cleaning, as well as if possible A repair?. The carburetor in photo is not mine but exactly the same. On the bottom the dommed cap mut has been broken off I still have the cap nut but the tube or whatever it was attached to it be broken from. Your service if possible I would be most grateful for. I would be willing to pay up to $200. for your service or anyone here if they can assist me. Or what be necessary for services. Shipping to and from you the carburetor I will certainly pay.

I am willing to rebuild your carburetor. Send me an email and we can discuss it. krinne at windstream dot net

1930 mccormick 22-36 carb

southcryn82

Member

Nebraska Cowman

Well-known Member

southcryn82

Member

Nebraska Cowman

Well-known Member

southcryn82

Member

Nebraska Kirk

Well-known Member

James Williams

Well-known Member

SweetFeet

Well-known Member

southcryn82

Member

LewissiweL

New User

Nebraska Kirk

Well-known Member

Similar threads