|
| |
| Farmall & IHC Tractors Discussion Forum |
Topic: MD Head Gasket
[Return to Forum]
| Author |
[Modern View]
|
| jfrankhash
02-19-2013 10:45:49
67.142.173.21
|
Trying to find an MD (very late 1952) head gasket. I keep running across references to engines with numbers like BD144, BD 154, D264, D281, D236, etc. Can anyone tell me how to tell what cubic inch diesel I have? Thanks, John
|
|
[Reply] [No Email] | |
| D Slater
02-19-2013 15:31:03
184.15.17.95
|
|
Re: MD Head Gasket in reply to jfrankhash, 02-19-2013 10:45:49
|
| Original engine model would be D-248. Then you need to know if its 3-7/8 bore, or changed from a 3-7/8 inch bore to 4 inch pistons. Then you get into 2 different type sleeves. Need to see how much the sleeves protrude above the deck and shape on top. Not common to still have 3-7/8 pistons and sleeves.
Double check me on this because I never used these new gaskets.
If you have sleeve flanges that raise above the block a good bit. Head gasket 119166A1. For flanges even or just above, gasket 225604A1.
This post was edited by D Slater at 16:11:17 02/19/13.
|
[Reply] [No Email] | |
| Mdnut
02-19-2013 13:14:18
71.215.207.237
|
|
Re: MD Head Gasket in reply to jfrankhash, 02-19-2013 10:45:49
|
| Md's had a d248 block used two head gaskets one for stock pistons and one for factory 4" pistons super mds smtads and 400ds used the d264 block and 450d used d281 block people need correct info clowns just posting stuff on here wasting everyone's time
|
[Reply] [No Email] | |
| rustred
02-19-2013 14:38:29
69.58.16.5
|
|
Re: MD Head Gasket in reply to Mdnut, 02-19-2013 13:14:18
|
|  well we told you john, how to tell what cid diesel you have. i dont see where mdnuts is answering your question, other than posting stuff about the diff. bores. to find a 248 is rare.also when going to buy the gasket the parts man would ask what bore it is.
and now back to the show!
|
[Reply] [No Email] | |
| mkirsch
02-19-2013 11:53:52
64.80.110.74
|
|
Re: MD Head Gasket in reply to jfrankhash, 02-19-2013 10:45:49
|
| Engine designation is cast into the side of the block somewhere.
On an MD you should find "D264."
|
[Reply] [No Email] | |
| Jerry Crow
02-19-2013 11:08:15
72.148.4.105
|
|
Re: MD Head Gasket in reply to jfrankhash, 02-19-2013 10:45:49
|
| If you have the stock motor it should be the 264 Cu.in.
|
[Reply] [No Email] | |
| rustred
02-19-2013 11:07:38
69.58.16.5
|
|
Re: MD Head Gasket in reply to jfrankhash, 02-19-2013 10:45:49
|
| just measure the cyl. bore. most likely have the 264 which is 4" bore
281 is 4 1/8 bore.
cu. in.displacment = # of cyl's x 0.7854 x bore2 x stroke.
|
[Reply] [No Email] | |
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
