|
| |
| Farmall & IHC Tractors Discussion Forum |
Topic: hand crank?
[Return to Forum]
| Author |
[Modern View]
|
| mschwartz
11-16-2012 19:17:38
216.163.99.163
|
Could anyone tell me if the starting cranks were the same for the F-series tractors and the farmall H and M? I know that some were longer for the wide front axle. Mostly wondering if the slot in the end for the starting pin coming out of the bolster was in line with the bend in the handle or was 90 degrees off? Have some that are both ways but not sure if they have been modified or not. Thanks, Mike
|
|
|
|
| Janicholson
11-17-2012 11:24:31
96.24.99.126
|
|
Re: hand crank? in reply to mschwartz, 11-16-2012 19:17:38
|
|
| I can give an answer that works!!
When put on the crank drive, and pushed in to engage the crank, the handle of the crank should be at the bottom, or 15 to 20 degrees clockwise from bottom. (assuming the engine was shutoff and allowed to stop naturally) inline 4 cylinder engines stop with the pistons about 1/2 way in the bores. Pulling up is the only safe (ish) way of cranking, and if the pin placement was incorrect, the handle would be in an unsafe position. Jim
|
|
|
| Arnold Layne
11-17-2012 08:22:53
66.146.251.119
|
|
Re: hand crank? in reply to mschwartz, 11-16-2012 19:17:38
|
|
| The coupling on an H and M crank is smaller than an F series, the F will work on an H or M but not vice versa.
|
|
|
| badger bob
11-17-2012 05:24:24
74.36.198.34
|
|
Re: hand crank? in reply to mschwartz, 11-16-2012 19:17:38
|
|
| I have some cranks around hear that are to small ( hole in the end) to fit my f20 i though that thay were for the m or h . Bob
|
|
|
| Mark Poss
11-17-2012 04:24:08
173.25.60.148
|
|
Re: hand crank? in reply to mschwartz, 11-16-2012 19:17:38
|
|
| My handcrank for my H fits my F-20
|
|
|
| blunted
11-16-2012 19:29:41
208.126.59.145
|
|
Re: hand crank? in reply to mschwartz, 11-16-2012 19:17:38
|
|
| you would think thay would be straite, if im getting you rite. i know my a has the crank, but is bigger in diamater for the balster in front of my sc..
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
