|
| |
| Farmall & IHC Tractors Discussion Forum |
Topic: wide front question
[Return to Forum]
| Author |
[Modern View]
|
| kennell
08-26-2012 05:49:44
142.68.102.232
|
|
| caterpillar guy
08-26-2012 20:45:36
68.188.235.228
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| I don't know why you would be still lingering here just buy it and count the change. It is so cheap I might even be interested in a hydro and I don't even like them.
|
[Reply] [No Email] | |
| Ron 1456
08-26-2012 15:13:11
173.215.55.203
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| The rear support is different.
|
[Reply] [No Email] | |
| DeltaRed
08-26-2012 16:02:32
67.6.225.104
|
|
Re: wide front question in reply to Ron 1456, 08-26-2012 15:13:11
|
| Different how?
|
[Reply] [No Email] | |
| Ron 1456
08-26-2012 16:30:38
173.215.55.203
|
|
Re: wide front question in reply to DeltaRed, 08-26-2012 16:02:32
|
| 2 inches taller or shorter but I don't remember which. Put a 560 wide front on a 450 onetime and got a different rear support for it off an "M". Still have it.
|
[Reply] [No Email] | |
| RPM1941
08-26-2012 11:50:34
173.23.76.185
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| You will need 4 of 51693D wedges for the rear saddle bolts on the top side to offset the taper of the angles of the bolts to inside of channel. When you get them they will explain themselves.
|
[Reply] [No Email] | |
| kennell
08-26-2012 08:02:56
142.68.102.232
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| That wouldn't be to series. Thanks guys Kent
|
[Reply] [No Email] | |
| Allan In NE
08-26-2012 08:18:40
148.66.98.174
|
|
Re: wide front question in reply to kennell, 08-26-2012 08:02:56
|
| | Use a 1/2" drill and a floor jack. Those frame rails are pretty darned soft and easy to drill. Allan
|
[Reply] [No Email] | |
| DeltaRed
08-26-2012 07:57:02
67.6.225.104
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| Yes.You will have to drill four 1/2" holes in the underside of the frame rails for the stabilizer support.
|
[Reply] [No Email] | |
| SD pete
08-26-2012 07:45:48
24.230.34.249
|
|
Re: wide front question in reply to kennell, 08-26-2012 05:49:44
|
| If i remember right it should. If it doesnt all it would take is to drill a couple of holes.
|
[Reply] [No Email] | |
| 504
08-26-2012 13:16:42
64.111.61.44
|
|
Re: wide front question in reply to SD pete, 08-26-2012 07:45:48
|
| Then, how much for what is left?
|
[Reply] [No Email] | |
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
