Yesterday's Tractor Co. New Parts for Old Tractors
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Farmall & IHC Tractors Discussion Forum
Show Parts for Model:

IHC 915 combine

Welcome Guest, Log in or Register
Author  [Modern View]
R Miller

06-20-2011 20:27:15
64.246.123.133



Report to Moderator

I have a problem with combine. Can't clean up the grain going to the grain tank. Something is wrong inside the machine and i can't figure it out. All the bean pods and other trash that should be blown out the back is going into the tailing elevator and ends up in the clean grain. Also the trash actually piles up inside the machine to where i have to get inside and clean the pile out by hand, after its cleaned out it will be fine for a bit until it piles up again. There was a canvas curtain that hung inside behind the cylinder that is gone .. is this part of the problem? Thanks for any help.

[Log in to Reply]   [No Email]
RPM1941

06-21-2011 18:42:44
173.25.71.175



Report to Moderator
 Re: IHC 915 combine in reply to R Miller, 06-20-2011 20:27:15  
Sounds like lower sieve has a hole or part of it missing, its hard to see, not much room, try a flashlight, front section probably, take it out the back, all 915 same size, different finger length, short for wheat & other small grain, long finger on later series for corn. The separator fan belts are prone to slip at higher rpm, they wear on the width not length.



[Log in to Reply]  [No Email]
soybeanjoe

06-21-2011 04:58:25
66.213.171.108



Report to Moderator
 Re: IHC 915 combine in reply to R Miller, 06-20-2011 20:27:15  
Sounds like the sieve either has some missing finger sections or is broken. Not uncommon on those machines, even back when they were new.



[Log in to Reply]  [No Email]
Brownie 450

06-21-2011 03:43:49
66.43.241.198



Report to Moderator
 Re: IHC 915 combine in reply to R Miller, 06-20-2011 20:27:15  
How are the sieves? Any fingers missing? How are they set? They should be set so that your fingers can just slide in between the sets of fingers. Make sure that there aren't any concave problems [holes or wires missing. The baffle behind the cylinder/concaves might cause trouble, but should be in place. How is the belt that drives the cleaning fan? How about a bad bearing on the cleaning fan? Take a look where the fan delivers air to the sieve area to make sure air flow isn't being blocked.
As noted, check the shakers --both sides for good action. Bushings should be in good shape & carry the sieves without dragging.

[Log in to Reply]  [No Email]
minnemoman

06-20-2011 21:09:59
69.89.205.141



Report to Moderator
 Re: IHC 915 combine in reply to R Miller, 06-20-2011 20:27:15  
is the cleaning fan working good it sounds like you arn't getting enuf air to the sives, if it has the even flow cleaning fan there could be a leak between the fan and the sives, reducing the air through them.
also make shure the cleanning shue is moving the full distance from frunt to rear becouse if it isn't that can cause loading of the sives and on a macine that old a little play in most of the shue drive componets can add up to short move ment

good luck and have fun :)

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters