(800) 853-2651
SHOP NOW

Farmall 806

A

avant 1735

Member
Has anyone out there ever put a foot feed (accelerator pedal) on an 806. Sure would be handy for me if I had one. Looking to put one on and wondering if anyone has done it, and willing to give me some good advice. Thanks
 
Well if it's a diesel, I would think it would be pretty easy with the injection pump on the right side of the engine, i never done it on mine, but i would go look at a John Deere 4020-4620 they have them, and the pump is on same side, on the 4620 you go from idle to wide open with out too much foot movement.
 
IH offered one. I saw one in my owners manual under the 'optional equipment' section.There is now an outfit that makes them. Seen them advertise in RedPower Magazine at times.Try Googleing '806 foot throttle'
 
One of the most useless things Deere ever put
on their tractors. IMHO.

Second most dumb thing on the 4020s was sticking
that PTO lever out on the right side to catch
winter clothes when getting off.

One of Harvesters classic blunders was putting
the transmission dipstick under the floor board
on the 1066.
Jim
 
I rather like the foot throttle on the 4020. I find it handy when doing loader work,or other jobs that take a lot of back/forth;stop/start.I've often thought of putting a foot throttle on my tractor.The PTO lever doesn't bother because I always get off or the left.If I ever get off on the right,I just 'compensate'. However,I whole heartedly agree about the IH dipstick!the guy who designed that was a real 'dipstick'.
 
Delta---- I suppose where it is needed, it would be
handy.
Biggest aggravation with the PTO lever is that I use
it to pull in loads. Due to space limitations & geography,
our wagons dump on the right side, so it is handier to get
off/ on on the right side.
Jim
 
I worked for a farmer after college that had a 1066 with a factory foot throttle.I am sure this style could be adspted to an 806. It was factory I-H. This was very handy when hauling wagons down the road or hauling manure. You set the throttle while in the feild. but use the foot feed everywhere else. I install factory, or shop built pedels on most all of my tractors that get used much. AL
 
You must log in or register to reply here.

Similar threads

C
806 turbo replacement
Replies
4
Views
377
the tractor vet
T
B
Farmall 806
Replies
4
Views
613
BarnyardEngineering
BarnyardEngineering
crsutton81
IH / Farmall sign
Replies
7
Views
787
BarnyardEngineering
BarnyardEngineering
F
Titan tires for pulling
Replies
8
Views
319
HFP
HFP
M
Farmall 560 deluxe seat upholstery
Replies
2
Views
192
the tractor vet
T
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top