(800) 853-2651
SHOP NOW

Minor super c headache

L

Leo Haddox

Member
I know the last thing people like to do is answer
stupid questions, but I've only owned the tractor a
couple weeks and promise to buy a shop manual
soon. I was out blading snow this morning on my
Super C with a front mounted blade, and on my last
scrape across the parking lot I hit a cement curb
with my blade. Then I was unable to lift me front
blade. It appears there was a 3/8ths bolt or retainer
that held thing together as it rocked up and down, on the left front rock shaft side.
Half of it is still stuck in the back section that move
up and down, but the front section fell out when it
broke. From the look of the back piece it has
threads plus a cotter key. My question is this a
special part or will a 3/8 x 3 3/4 machine bolt work.
Just curious, don't want to mess anything up.
Thanks. Lh
 
I've got a Super C with a front blade and I still don't know what your talking about, Post a picture. Also have the manual for the IH blade, number 72 blade I think.
 
Just taking an educated guess but I bet that bolt is a common bolt that had a castle nut on it and the cotter pin is used to lock the castle nut on the bolt. I would use a grade 8 bolt and a lock nut on it. Ya you might be able to find a bolt with a hole already drilled for the cotter pin but a lock nut is likely to work just as well
 
Does your blade look something liket this one?
a247419.jpg
 
On the left there are two rockshafts. The outer for the front implements and the inner for the rear. As I remember, the two have little clearance between them. Ours have pins in them, under a spring loaded keeper. The pins are 3/8" or thereabouts X 1 1/2" long, or so. You can get some, or something similar that will do, at a tractor supply place. Make sure whatever you use, that it doesn't extend into the inner rockshaft and create interference. If it's in a different location, or I'm remembering wrongly, ignore this advice and, quite likely a bolt will do.
 
You must log in or register to reply here.

Similar threads

C
Super C input shaft seal replacement
Replies
1
Views
104
Charlie M
C
C
Wire for Super C lights
Replies
5
Views
262
Bull Gear
B
C
Wiring lights on a Super C
Replies
6
Views
227
560Dennis
560Dennis
M
Super C Carb Identification
Replies
4
Views
247
mainer76
M
D
Neighbor lady's Super C
Replies
8
Views
847
used red MN
U
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top