Yesterday's Tractor Co. We Have the Tractor Parts You Need
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Database Forum Testing Area

S C Connecting rods

Welcome Guest, Log in or Register
Author  [Modern View]
L. LAMP

11-18-2012 10:22:54
12.73.110.233



Report to Moderator

I was checking to see if any of my rods were bent by laying them face to face with the caps in the same direction and with both rods slipping over a ristpin. I considered them good if the big end made full contact. However, I observed that the space between the ristpin holes changed from 1/4" to 1/8" when I flipped the rods over so the caps were facing opposite directions. These rods were marked ATLAS 7. Of all the rods I have, there are ATLAS 6,7,8,and 9'S from various engines. What do these markings indicate? I want all of them to have the same number. They do appear to be a little bit different in some areas. I have read in posts here that the rods can be installed with the caps to either side of the block. I wanted them installed so the power stroke was on the heavy side of the rod and not the bolt as the manual says to install them. If the cap is to the carb side the rod will not be centered between the ristpin bosses in the piston. Installed per manual, the ristpin hole is wider toword the back side of the engine, so therefore should NEVER be reversed. Any other thoughts or discussion on this?

[Log in to Reply]   [No Email]
El Toro

11-22-2012 06:15:24
108.3.143.30



Report to Moderator
 Re: S C Connecting rods in reply to L. LAMP, 11-18-2012 10:22:54  
Rods are usually installed with their numbers facing toward the camshaft. Hal



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters