Yesterday's Tractor Co. Fast, Friendly Parts Service
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Database Forum Testing Area

SC engine pistons wrist pins

Welcome Guest, Log in or Register
Author  [Modern View]
BoonvilleKid

07-12-2012 06:12:30
24.206.167.192



Report to Moderator

Two questions: (1) How can one determine if piston wrist pins need to be replaced when replacing rings, crankshaft bearings & new head valves? They feel like factory new, but have no way to test them. (2) Engine has flat-head pistons. Was wondering if replacement with firedome pistons would raise horsepower, and if so, by how much.




[Log in to Reply]   [No Email]
El Toro

07-15-2012 13:08:44
108.3.148.85



Report to Moderator
 Re: SC engine pistons wrist pins in reply to BoonvilleKid, 07-12-2012 06:12:30  
Why don't you buy a new sleeve kit that has new pistons and rings. Take the old connecting rods to your local auto machine shop and have them install the new pistons. They will make sure the wrist pins have the correct clearance.

Have the crankshaft measured for wear and buy your bearings from the machine shop. They can determine if the shaft needs to be ground undersize. They won't do it unless it needs it. If the shaft has undersize bearings they can furnish the correct bearings. It's possible it may have been ground undersize.

Have them do a valve job. If the valves are getting thin 1/32" replace them. If the guides are worn replace them. I would also replace the valve springs. Then you engine will last a long time . Hal

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters