(800) 853-2651
SHOP NOW

new case identity unknown

D

deene

Member
hi guys just bought my second case ever..1st was a vai that was in bad shape this one runs but I don't really know what it is..guy I bought it from said its a 300 but it doesn't have the round nose..its the square with the 2 grill screens..its a utility I would say low to ground fixed wide front diesel..manual trans with hi low lever on the right of operator..has a lever to the left that he said would stop the tractor moving but still run pto..has 14.9 24 on rear..pressed steel...has 3pt with eagle hitch..what could this be?...any quirks about the diesels I should be aware of ..I think this one wetstacks some as it has trails of black from manifold into muffler but it started up and ran good without smoking...the throttle lever doesn't work its on the left side of the steering wheel and moves but doesn't move the linkage?..any thoughts on that..thanks for all the input..im excited to get it...thanks again
 
It sounds like you might have a 300B, or possibly an early 430. If it's the former, it has a deisel engine made by Continental and there were only 64 of them made from 1958-1959.
 
Just to add a bit, to Joe's comment. The Continental deisel will have the exaust stack on the RH side of the hood. The Case 188 will have the exaust on the LH side.
Loren
 
it has the exhaust on the right hand side when sitting on the tractor...if it is only one of 64 I bet parts are hard to come by..i think it is a 300b..when looking at pics on here in the gallery that"s what it looks like..are they good engines..it does have a red seal decal on the valve cover..what about the throttle linkage..any insight on whats loose there?..thanks again for the help
 
The red seal decal is definitly a Continental engine. Nice find! It is the same as a 300 round nose, but has different sheet metal, so there were more than 64 made. Don L or John S on this forum will most likely be able to help you with parts for your tractor.
Loren
 
thanks for the info I don"t know those guys since Im not on here much who could I chat with about the linkage problems and such..thanks again
 
You must log in or register to reply here.

Similar threads

H
  • Question
Case 1370 Hydraulic remote control lever hard to move under pressure.
Replies
3
Views
380
KDR12
K
L
VAI Case - Only 2-3 PSI Oil Pressure
2
Replies
29
Views
802
LeFeu
L
CaseDC3
400 and new to me BH Plow
Replies
8
Views
292
CaseDC3
CaseDC3
P
90 Series case remote coupler locations??
Replies
2
Views
309
want@1070
W
F
1954 Case 500
Replies
1
Views
338
Don Rudolph
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top