Yesterday's Tractor Co. We Have the Tractor Parts You Need
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Case Tractors Discussion Forum
Show Parts for Model:

1957-1962 Case 320 backhoe clutch pressure plate adj.

Author  [Modern View]
Jim Legault

07-05-2012 12:36:11
97.113.115.121



Report to Moderator

could anyone help me with the tension adjustment on the pressure plate? I'm not familiar with this, i have never had to adjust the pressure plate before.




[Reply]   [No Email]
mEl

07-05-2012 15:05:02
96.249.136.9



Report to Moderator
 Re: 1957-1962 Case 320 backhoe clutch pressure plate adj. in reply to Jim Legault, 07-05-2012 12:36:11  

Jim Legault said: (quoted from post at 12:36:11 07/05/12) could anyone help me with the tension adjustment on the pressure plate? I'm not familiar with this, i have never had to adjust the pressure plate before.


Don't know about the "tension" adjustment you are referring to, the clutch pressure is set on some pressure plates by the finger height and there is a fixture that dealers have to properly set them. It is a cast plate with a protrusion that comes out to the finger area and the fingers are set off the face of that tool to proper finger height. Most people do not have access to those tools. Free travel adjustment is another matter, the rod adjustment should be adjusted by lengthening if there is to little or shortening the rod that goes into the bell housing if ther is to much. The free traavel should be min 1.5 in.

mEl
This post was edited by mEl at 15:05:30 07/05/12.

[Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Add a Reply]

Hop to:
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters