(800) 853-2651
SHOP NOW

wc hub thread size

R

RR Performance

New User
Can anyone tell me the thread size and pitch for the holes in the rear wheel hubs of a wc? Where the wheel bolts to the hub. Thank you.
 
IIRC 5/8 coarse. Std coarse is 11 tpi? Not near my books or tractors. Heck, not even MN! Other end of the river.
 
Now I know why it is getting so cold down south you drug it with you. You know there are a number of guys who think you should have left the cold up there
 
I thought I did- it was minus 16 when I left it there last Tuesday. Currently freezing rain in NO! Parked for awhile.
 
Hope your not driving around down there. Them people in the south once so much as a flake of snow hits the ground drive like they are in bumper cars and keeping between the ditch is impossible for them
 
Tried to find a restaurant open for supper.......all closed within many miles, found a McD. Bought some groc this AM but wanted to save that for Wed if needed. Mostly cops and town utility folks on the road, just monitoring. Interstates closed down, lotsa other roads as well.
 
Ya down in the south they get an inch of snow they close the road till it has gotten above freezing. Still remember a number of years back when a cop pulled my dad over for driving on a snow covered road with maybe 1-2 inches. My dad asked the cop why and he said road are not safe and may dad told him what the heck this is nothing compared to what we had in Minnesota. Cop said you from MN my dad said yes so the cop said go right ahead. Or another time my dad won a bet with home MS High way patrol. The roads had ice on them and my dad was teaching a criminal justice class with them. The y saw where he was parked and said there is not way your going to pull out of there with out spinning you back tires. My dad said you want to bet me on that?? They said yes. Well he did not spin his back tires but did spin the fronts a tad bit. He had borrowed my car which was front wheel drive. They lost the bet and had to pay up
 
You must log in or register to reply here.

Similar threads

J
WC front hitch
Replies
2
Views
239
jpi72
J
C
WC or WD?
Replies
8
Views
480
C.Amick
C
J
Sludge in WC oil pan
Replies
13
Views
559
jpi72
J
L
MM RTU Engine Pressure Relief Valve
Replies
4
Views
315
T.R.K.
T
J
Dual Hub Bolt Pattern
Replies
0
Views
177
jsferden
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top