|
| |
| Allis Chalmers Discussion Forum |
Topic: cam bushings
[Return to Forum]
| Author |
[Modern View]
|
| r. j. tomlinson
02-20-2012 14:44:20
76.201.159.70
|
should i replace in wd 45 & wc and what are they.. i also need a good parts catolog to order from ,,thanks
|
|
|
| S.C.
02-21-2012 11:30:14
174.253.28.39
|
|
Re: cam bushings in reply to r. j. tomlinson, 02-20-2012 14:44:20
|
|
| I would measure the cam and bores. They are probably just fine. The one I rebuilt a while back measured same as new and it's never had the bushings replaced.
|
|
|
| BushogPapa
02-20-2012 18:54:31
173.88.50.86
|
|
Re: cam bushings in reply to r. j. tomlinson, 02-20-2012 14:44:20
|
|
|
Look them over and see if any bearing material if obviously missing...Not just superficial color from light wear.. They are not heavily loaded and probably are just fine.. Remember, the cam gets the oil BEFORE it goes to the rod and Main bearings.. Ron..
|
|
|
| JMS/.MN
02-20-2012 17:57:27
209.237.107.155
|
|
Re: cam bushings in reply to r. j. tomlinson, 02-20-2012 14:44:20
|
|
| Measure to see how worn they are. I&T AC 11 manual has the specs.
|
|
|
| r. j. tomlinson
02-21-2012 08:03:58
76.201.159.70
|
|
Re: cam bushings in reply to JMS/.MN, 02-20-2012 17:57:27
|
|
| JMS/.MN
02-21-2012 18:24:11
209.237.107.155
|
|
Re: cam bushings in reply to r. j. tomlinson, 02-21-2012 08:03:58
|
|
| I made a removal/installation tool on the lathe. Solid steel plug with one diameter that fits inside the bushing, outer diameter slightly under bushing OD. Solid shaft for handle, pushes worn bushing out, new bushing in. Make sure you locate oil hole properly on install.
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
