International Harvester / Farmall Super W4 Parts

[Categories]   [All Super W4 Parts]   [All Farmall Models]  

Drawbar Pin Retainer Plate - Used on the following Farmall / International models: H, M, 560, 806, 1066, MD, MTA, W6TA, W9, O4, WD9, WR9, Super WDR9, OS4, Super H, Super M, Super MD, Super MTA, Hydro 84, Super W4, Super W6, Super W6TA, Super WD6, Super WD9, W4, W6, WD6, WDR9, WR9S, 300, 330, 340, 350, 400, 450, 454, 460, 464, 504, 544, 574, 600, 606, 650, 656, 660, 664, 666, 674, 706, 756, 766, 826, 284, 856, 966, 1026, 385, 484, 584, 684, 686, 784, 884, Super MDTA, Super WD6TA, Super WR9S, Super W9, WD6TA, this part measures 1.480 inches long, 1 inch wide and has a 0.377 inch hole diameter and 0.193 inch thick. Many of the listed models used a round plate rather than the rectangular one. This part will replace the round version. Replaces OEM numbers 132794H1, 491390, 49139D, 57654D, 57655D, 58657D (Item #: 112643, Ref: 49139D) $7.50
Universal Parts and Accessories Category: Hitch / Drawbar
Center Link Pin - For tractors using a Category 1 3 point hitch. Pin diameter of 3/4 of an inch. Usable length of 3 inches. Overall length of 4 15/32. Head diameter of 7/8 of an inch, with a 1/2 inch hole. Fits many models. Verify dimensions for your specific application. Can be used with DKP14 linch pin. (Item #: 108702, Ref: 957E560) $1.80
Check Chain and Pin Kit - Includes 1 Chain and 2 Clevis with pins and cotters. For most early models, pre-1965, category 1. (Item #: 111334, Ref: CBPN598A) $9.10
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $373.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $371.87
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $444.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $444.00
Drawbar, Universal Cat I, 20-1/2 Inch - Universal Category I Drawbar Measures: (A) 1-7/64 inches thick, (B) 2-3/8 inches wide, (C) 20-1/2 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 2-1/32 inches from body edge to center of first body hole, (F) 3-3/32 inch center to center between holes, (G) 7/8 inch end pin, (H) Five 25/32 inch holes. (Item #: 179615, Ref: S.49123) $60.00
Drawbar, Universal Cat I, 25-1/2 Inch - Universal Category I Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 25-1/2 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 4-29/64 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 7/8 inch end pin, (H) Seven 25/32 inch holes. (Item #: 178799, Ref: S5009) $40.40
Drawbar, Universal Cat I, 29-3/4 Inch - Universal Category I Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 29-3/4 inches center to center on lower link pins, (D) 1-15/16 inches from center of pin to edge of body, (E) 4-1/2 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 7/8 inch end pin, (H) Nine 25/32 inch holes. (Item #: 178800, Ref: S128196) $48.80
Drawbar, Universal Cat I, 30-1/8 Inch - Universal Category I Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 30-1/8 inches center to center on lower link pins, (D) 2-1/16 inches from center of pin to edge of body, (E) 2-3/8 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 7/8 inch end pin, (H) Eleven 25/32 inch holes. (Item #: 103174, Ref: S125) $44.30
Drawbar, Universal Cat II, 30-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 30-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 2-3/8 inches from body edge to center of first body hole, (F) 2-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Eleven 25/32 inch holes. (Item #: 103176, Ref: S126) $58.00
Drawbar, Universal Cat II, 30-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-1/4 inches thick, (B) 3 inches wide, (C) 30-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3 inches from body edge to center of first body hole, (F) 2 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Eleven 3/4 inch holes. (Item #: 103176, Ref: S60155) $58.00
Drawbar, Universal Cat II, 36-1/4 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 3-1/8 inches wide, (C) 36-1/4 inches center to center on lower link pins, (D) 2 inches from center of pin to edge of body, (E) 3-35/64 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Nine 1-19/64 inch holes. (Item #: 179623, Ref: S15134) $138.00
Drawbar, Universal Cat II, 36-29/32 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 36-29/32 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3-9/16 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Nine 1 inch holes. (Item #: 179670, Ref: S3394) $99.00
Drawbar, Universal Cat II, 36-3/4 Inch - Universal Category II Drawbar Measures: (A) 1-1/4 inches thick, (B) 3 inches wide, (C) 36-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 3-7/8 inches from body edge to center of first body hole, (F) 2 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Thirteen 3/4 inch holes. (Item #: 103177, Ref: S60156) $71.00
Drawbar, Universal Cat II, 39-3/8 Inch - Drawbar, Universal Cat II, 39-3/8 Inch - Universal Category II Drawbar Measures: (A) 1-3/16 inches thick, (B) 2-3/8 inches wide, (C) 39-3/8 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 7-7/8 inches from body edge to center of first body hole, (F) 3-1/8 inch center to center between holes, (G) 1-1/8 inch end pin, (H) Seven 1-1/8 inch holes. (Item #: 179583, Ref: S15081) $104.00
Drawbar, Universal Cat III, 42-3/4 Inch - Drawbar, Universal Cat III, 42-3/4 Inch - Universal Category III Drawbar Measures: (A) 1-49/64 inches thick, (B) 3-1/2 inches wide, (C) 42-3/4 inches center to center on lower link pins, (D) 2-3/8 inches from center of pin to edge of body, (E) 5-61/64 inches from body edge to center of first body hole, (F) 4-21/64 inch center to center between holes, (G) 1-27/64 inch end pin, (H) Seven 1-1/4 inch holes. (Item #: 180531, Ref: S29139) $298.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.50
Leveling Assembly - Universal Economy Leveling Assembly. 1-5/16" body of high strength tubing, thread size, 7/8" fine thread-study clevis at each end with 5/8" pin holes. May be used right or left. Can Replace NCA577A and Fork. 18 inches closed, 28 inches open. (Item #: 154104, Ref: LB152) $47.71
Lift Arm Bushing - This Bushing is for using Category I Implements with Category II Lower Lift Arms. It has a 7/8 Inside Diameter, and 1-1/8 Outside Diameter and is 1-3/4 Inches long. Replaces B500192, 87299215, 87760407, EC0NG992AA, 150-821, BUSH04, 22BCO006, 477RB, BO821, 2430351, B821, B2008, 351, 00351, C7NNG992A, 81819374 (Item #: 108626, Ref: BUSH04) $2.60
Linch Pin, Pack of 2 - Package of 2 linch pins. Pin diameter 5/16 inch, useable length 1 1/4 inch, Ring diameter 1 5/8 inch. Cold Forged. (Item #: 153791, Ref: DKP516) $1.20
Linch Pins, Pack of 2 - Pin diameter 1/4 inch, useable length 1 1/4 inch. Cold Forged. Enter 1 for package of 10. (Item #: 153789, Ref: DKP14) $1.10
Linch Pins, Pack of 2 - Package of 2 linch pins, 7/16 inch diameter pin x 1-3/4 inch usable length, 1-5/8 inch diameter ring. Cold Forged. Enter 1 for package of 2. (Item #: 153792, Ref: DKLP91) $1.20
Linch Pins, Pack of 2 - Linch Pins. 3/16 inch outside diameter pin x 1-1/4 inches Long. (Item #: 153788, Ref: DKP316) $1.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 490mm (19 15/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches). Verify that the measurements will meet the requirements of your application. (Item #: 185049, Ref: 159332) $43.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 21.5 Inches Center to Center (A), Thickness: 5/8 inches, Width 2 9/16 inches, 7 1/4 Inches from center of ball joint for first hole (B), 9 1/4 inches from center of ball to second hole (C). Verify that the measurements will meet the requirements of your application. (Item #: 103203, Ref: 159324) $39.30
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 595mm (23-7/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 13-3/4 inches, 12 inches and 8-1/2 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 185732, Ref: 159326) $58.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 645mm (25 13/32 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 14-3/4 inches, 13 inches and 8-1/2 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 184428, Ref: 159328) $60.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 700mm (27 9/16 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), Three holes located 16-1/4 inches, 13 inches and 6-1/4 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 103206, Ref: 159330) $64.00
Lower Lift Arm, RH or LH, CAT I - This Lower Lift Arm is a universal part. It is not designated to fit any specific model. Order by size. If the measurements are not exactly what you are replacing, consider ordering a matching pair. Measures; Length: 750mm (29 1/2 inches), Thickness: 16mm (5/8 inches), Width: 65mm (2 9/16 inches), One hole located 6 1/4 inches from center of ball. Verify that the measurements will meet the requirements of your application. (Item #: 103207, Ref: 159322) $64.00
Mower Deck Height Stabilizer Kit - Fits all category 1 tractors. Chain length is 40 inches. Maintains consistent mower height and eliminates need for stabilizer bars. Contains two top brackets and two lower brackets with chain. (Item #: 103201, Ref: MHSK1) $39.00
Quick Hitch A-Frame Design - Makes for easier implement attachment, by use of self-aligning steel roller. System self-aligns as tractor’s 3-point hitch is raised. This is a CE Approved, Cat I. 2645 pound capacity. For implement side adapter, see part number S23465. Additional $200.00 shipping due to weight. (Item #: 179003, Ref: S110168) $335.41
Quick Hitch A-Frame Implement Adapter - Used with S110168 quick hitch, this is a weld on bracket. The load capacity is3306 pounds. (Item #: 179380, Ref: S23465) $103.21
Quick Hitch, Category I - Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed. This part ships via truck freight. Please call for pricing and ordering. (Item #: 180731, Ref: HF141101) $332.00
Stabilizer Assembly - This Stabilizer Assembly measures 14 inches minimum to 17.5 max. It has 7/8 inch pin holes and 12 degree bend on the link side. This part is sold a a universal part. Verify measurements before ordering. (Item #: 179605, Ref: 343437X1) $21.50
Stabilizer Chain - This Stabilizer Chain is sold as a universal part. Verify measurements before ordering. It is Adjustable 11.75 inches to 13.5 inches with a 3.5 inch body. 7/16 inch Pin Diameter. (Item #: 173628, Ref: 159350) $28.00
Stabilizer Chains, Set - 1 SET OF 2 stabilizers for ford tractors having an extra link which allows easy attachment to large and small model tractors by uncoupling the clevis and pin and moving up or down one link of the stabilizer accordingly. (Item #: 174066, Ref: SK102CH) $65.00
Stabilizer Link - This Stabilizer Link is used on Compact Tractors. It adjusts from 15.5 inches to 19.5 inches. The Link Side is 0.79 inches. The Eyelet Side is 0.90 inches. This part is sold as a universal part. Verify measurements before ordering. (Item #: 179606, Ref: VPL3232) $30.60
Top Link - Economy Top Link, 16 inch body. Category 1, 3/4 inch balls. Adjusts 20.5 to 29 inches overall. Dichromate plated center body. OEM JSA5050 (Item #: 184512, Ref: 30533E91) $26.70
Universal Drawbar Lock - For CAT I drawbars only (drawbars that are 1 inch thick x 2-1/2 inch width) . Prevents drawbar from rotating. (Item #: 178107, Ref: 49A29) $26.10
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $33.30