International Harvester / Farmall Super W6TA Parts

[Categories]   [All Super W6TA Parts]   [All Farmall Models]  

No Picture Connecting Rod Bolt Lock Tab - .490 inch bolt hole diameter, 8 used per engine, sold individually. For tractor models (I6, M, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6-61, W6, 400, 450 gas, LP with C248, C264 and C281 engines 8 used), (WD9, WDR9 early diesels up to engine serial number 10265 16 used). (Item #: 167084, Ref: 47496DB) $6.90
Cylinder Head - This is an LP Head for a 400, 450 LP. It will increase compression if replacing a GAS Head. Head includes guides and seats. Order part number 122658 LP high compression valve train kit which is required for engines switching from a gas cylinder head to the LP cylinder head as the LP head uses longer valves than the gas.As this is a BARE casting with guides and seats, customer is responsible for all final machining including head surfacing and machining for push rod clearance if needed. When mounting on a M or SUPER M there is no provision for the air cleaner breather line to rear of head, just block it off. For models 400, 450, M, Super M, Super MTA, MV, O6, OS6, W6, T6, Super MV, Super W6, Super W6TA, W400, W450, all with C248, C264 or C281 gas or LP engines. (Item #: 121586, Ref: 364586R11) $1069.01
Cylinder Head Stud - 1/2 inch x 7 1/16 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178330, Ref: 49023DA) $17.60
Cylinder Head Stud - 1/2 inch x 6 7/8 inch. For gas and LP Models: I6, M, MTA, MV, O6, OS6, Super M, Super MTA, Super MV, Super MVTA, Super W6, Super W6TA, T6, U6, W6, 400, 450. (Item #: 178329, Ref: 46117D) $10.98
Governor Throttle Shaft Rebuild Kit - This Governor Throttle Shaft Rebuild Kit fits: H, HV, I4, I6, M, MV, O4, O6, OS4, OS6, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, T6, T6-61, U4, U6, W4, W6, 300, 350, 400, 450 all Gas and LP. Replaces: Cotter pin: 103361, Pin: 103494, Groove pin: 142952, Bushing: 45696D, Felt washer: 48493D, Lever: 6288D, Gasket: 48501D, 53877DB, 66272DA. Kit includes: lever, bushing, felt washer, (3) gaskets, groove pin, cotter pin, and pin. (Item #: 183906, Ref: IHS2559) $51.00
Governor Thrust Bearing - Bearing has a outer diameter of 1.575 inches, width of 0.472 of an inch, and an inner diameter of 0.510 of an inch. The lip has an outside diameter of 0.750 of an inch, the shaft has an diameter of 0.656 of an inch, and has 2 pin holes with an inner diameter measuring 0.186 of an inch. For the following models: H, HV, Super H, Super HV, M (gas), Super M (gas), Super MTA (gas), O4, O6, OS4, OS6, Super W4, W4, Super W6 (gas), Super W6TA (gas), W6 (gas), W9 (gas), WR9S (gas), B-275 (gas), B-276 (gas), 300, 350 (gas), 354 (gas), 400, W400, 444 (gas), 450 (gas), W450 (gas), 600 (gas), 650 (gas). Replaces 48250D, 48250DX, and ST506. (Item #: 183913, Ref: 351910R91) $81.00
NOTE Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).	NOTE
No Picture Valve Service Kit - Cylinder HEAD Service KIT For gas models 400, 450, M, MV, O6, OS6, Super M, Super MTA, Super W6, Super W6TA, W400, W450, W6. Contains: springs, guides, locks, (no valves). (Item #: 131581, Ref: VSKH264) $176.00
Valve Set, Exhaust - Gas Engine - Valve length is 5.875 inch. Single Exhaust Valve (C248 CID Gas 4-cylinder engine). Model M and MV, O6, OS6, W6 and (C264 CID Gas 4-cylinder engine. Stepped head high compression pistons.) Models Super M and MTA, Super W6 and W6-TA. (Item #: 108496, Ref: 50732DA) $16.00
Valve Set, Intake, Gas Engine - Valve length 5.875 inch. Single Intake Valves (C248 CID Gas 4-cylinder engine). Model M and MV, O6, OS6, W6 and (C264 CID Gas 4-cylinder engine. Stepped head high compression pistons). For tractor models Super M and MTA, Super W6 and W6-TA. (Item #: 128742, Ref: 50731DA) $10.40