Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Project Journal - Ford power steering repair
Handle: Ultradog MN  
Project Name: Ford power steering repair  
Tractor: 1955 - 196  
Started: 02:05 03/05/17  
Updated: 03:38 03/05/17  
Expand/Contract all Journal Entries   Show oldest journal entry on top
uploaded by 3rd party, no description entered.
03:38 03/05/17

uploaded by 3rd party, no description entered.
03:38 03/05/17

 03:38 03/05/17  Ford 4 cylinder power steering
It is very common for leaks to occur in the power steering columns of these tractors. This is caused by seal failure.
The good news is they are very easy to repair. The bad news is you have to pull the tin off to get at the steering column.
First we will purge all of the old oil out of the system.
Start the tractor and crack the hydraulic lines that go to the cylinders.
Turn the wheel back and forth. Add fresh hyd oil as needed to get all the old stuff out of there.
Yes it makes a mess everywhere.
Remove the steering wheel.
Remove the tin.
Mark the hydraulic lines that go to the steering cylinders so you can get them back in the correct locations.
Remove the upper column tube #46.
Remove big nut, spring washer and upper bearing and races #31,42,43.
Remove the hydraulic block taking great care to not let the plungers, springs and balls fall out on the floor as you remove it #34.
Remove the lower adapter #29.
Now clean everything up.
Install new lower seal #28.
Spring side of seal goes up.
Install new upper seal #44.
Spring side goes down.
In a seperate small pan disassemble the hydraulic block. I use lacquer thinner for this. Remove all the plungers, springs and balls and the center spool. Remove any rust with crocus cloth or a Purple 3M scrubber pad. The purple ones are fairly soft. Get them at a body shop supply.
Green scrubber pads are too aggressive.
Inspect all 3 springs. Make sure they are not bent or broken.
Now is the time to decide if you want to do the whole job and not half of it.
Remove the lower steering box from the tractor clean out all the oil and crud in the bottom, inspect the sector gears, renew loose bushings, renew sector seals and inspect the bearing in the very bottom of the housing. I recommend you do but that's your call.
Getting back to the column here,
Install new paper gasket #24.
Install lower adapter with new seal.
Bolt it down.
Install lower bearing and races.
Install new Oring #32.
Lightly grease and reinstall center spool into hydraulic block. Inner groove on spool goes to bottom.
Set the block on column. See photo. Note that the extra fitting is on right side at top.
Now we will load the plungers.
Notice the hole that the pencil points to.
Install one special plunger with horns up.
Install 2 balls. Install second special plunger horns down.
Install one ordinary plunger, then one spring, then a second ordinary plunger in all three of the other holes.
Now install upper races, bearing, spring washer (curved down) and nut. Tighten nut down till the spring washer is completely flat - not too tight - then back it off 1/6 turn.
Now take a small punch and "stake" the thin upper part of the nut into the groove on the shaft. This is important as it keeps the nut from loosening.
Install another Oring #32 on top of the hydraulic block.
Install the upper tube being careful not to damage your new seal.
Bolt it down.
Reinstall all 6 hydraulic lines.
Add fresh oil to the reservoir.
I use 134 D oil - same Hytrans or UTF you use in your transmission and rear end.
Start the tractor and test your work before you put all the tin back on.
Now go have a cold one as you've earned it.

Comments
YTSupport
19:11 07/16/17
Excellent write-up. I really like this sort of thing, because when you need it, it's a Godsend.
Return to Journal list

What are Project Journals?

Project Journals are a place where YT Community members can document their tractor and farm projects. Each journal created, can have many photos and accompanying text entries. You can also enable comments to allow other members of the YT Community to comment on your journal. If you do enable comments, it is up to you to moderate what people enter in your journal according to the site policy of Yesterdays Tractors. Journals may also be used as photo posting area, to post your photos of your farm, tractors and related photo topics. If you would like to create a journal, just be sure you are logged in to the Classic View of the forums, and a link will appear to do so when you next come to this page.
.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Modern Diesel Fuel in an Old Tractor - by Staff. This interestin discussion is from the Tractor Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Rebuilt Injection pump for J D 1010. Call or text for pictures or more imformation.free shipping.U.S. No core charge [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy