Yesterday's Tractor Co. Same-Day Parts Shipping Available
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life

Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Article Comments
Comments for Oliver%20550%20Clutch
Add to these Comments

jake wrote on Thursday, March 11, 2004 (PST):
  • There is no mention of the seals on the trasmission case[PTO hub, PTO shaft and hyd pump-clutch shaft. These should be changed every time the Z split and frequently the cause of oil leakage.
    don wrote on Thursday, March 11, 2004 (PST):
  • did you install a speedi sleeve on the crankshaft before insalling the seal? because seals get hard and are very abrasive and cut into the crankshaft surface and make a very bad groove in the metal and makes a bad sealing surface.
    Jim Farina wrote on Friday, October 22, 2004 (PDT):
  • Greg you are correct about the reason you were experiencing clutch slippage on you Oliver. The clutch is made by Auburn Clutch. The pressure of the springs is compounded by locating them under the release levers. The pressure is transmitted through the lever to the pressure plate. Auburn was the only clutch manufacturer to use this arrangement. It has a couple of advantages. Since the pressure is compounded, a lighter spring can be used offering a softer clutch pedal. Also, the base of the spring does not contact the cast iron plate directly therefore heat is not transmitted to the spring causing a them to lose there pressure in cases where the clutch gets overheated. Since the pressure is transmitted throught the lever, the lever height directly affects plate load. Your levers were contacting the throwout bearing near the outside indicating that some of the levers were high. The higher the lever, the less the spring will be compressed and produce less plate load. This clutch is unique in that if the linkage can handle it you can set the levers as low as possible to create a heavier plate load. Good job, Greg. Jim.
    jerry herger wrote on Friday, February 18, 2005 (PST):
  • Jim, Can you adjust the release levers without doing the split?
    Duane Eberhart wrote on Saturday, January 20, 2007 (PST):
  • If the fingers aren t adjusted to an equal height the clutch will chatter as you go to leave the pedal out to engage the clutch. I have a 1959 550 that I did a Z split and replaced the clutch assembly a few years ago, got the whole assembly at NAPA...but while in there I needed to rebuild the PTO clutch.
    Jim Broughton wrote on Friday, November 16, 2007 (PST):
  • Nice job, your tractor looks first-rate and I suspect you took as much pains on the other items as you did on the clutch ! NICE JOB !!! Jim B.
    wanis wrote on Tuesday, December 25, 2007 (PST):
  • we need price for this tractor
    Frankie Paulk--Destin,Fl wrote on Sunday, June 06, 2010 (PDT):
  • I'm restoring 3 late model 550 Oliver diesel tractors now; have failed to locate a much needed head for one these tractors. IF someone has info please call or E-Mail--850-460-6226
    Frankie Paulk--Destin,Fl wrote on Sunday, June 06, 2010 (PDT):
  • I'm restoring 3 late model 550 Oliver diesel tractors now; have failed to locate a much needed head for one these tractors. IF someone has info please call or E-Mail--850-460-6226
    Lowell R Roberts wrote on Tuesday, June 28, 2011 (PDT):
  • Would appreciate cost for of clutch repair you described in your article and also, if you, yourself would repair clutch assembly and PTO assembly if I were to ship you the item. Prefer to talk to you by phone if you would please call me at 812-834-8701. Thankyou.
    Mark wrote on Thursday, December 29, 2011 (PST):
  • Can anyone provide a good source for a clutch alignment tool for a 1959 Oliver 500 with gasoline engine? Any experience with anyone using a universal clutch alignment tool. thanks
  • TRACTOR   PARTS TRACTOR   MANUALS
    Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

    Home  |  Forums


    Copyright © 1997-2014 Yesterday's Tractor Co.

    All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

    TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

    Yesterday's Tractors - Antique Tractor Headquarters