Yesterday's Tractor Co. New Parts for Old Tractors
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life

Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Allis Chalmers Discussion Board

Re: d 14 wheel adj.


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Diydave on September 29, 2012 at 04:45:59 from (96.244.162.135):

In Reply to: d 14 wheel adj. posted by T-bob on September 28, 2012 at 20:31:14:

Pull off the clamps, one at a time. Rotate the wheel, so a clamp is in the 12 o'clock position. Remove the clamp, by unscrewing the 2 5/8 bolts that hold it to the wheel center, then slide the clamp, along the wheel rail, till it drops out. be careful to not lose the rail slider, that goes between the cam, and the rail. Take the clamp, and put it in a big vise, spray down with your favorite penetrating oil. lightly hammer, against the clamp hex face, and the rear face of the cam axle. If you have an air impact, use it, forward, and reverse, to get the cam turning. It is not threaded, it is a close fit. once you get it turning, dis-assemble the snap ring, at the rear, and punch the cam pin out the front of the clamp, and coat the wear areas with neversieze compound, and re-assemble. After the first one, you will get better, and they will take 20 minutes to an hour, to free up. As you free up each clamp, replace it, and move to the next.


Replies:




Add a Reply

Name:
E-Mail:
Subject:

Comments:

Optional Link URL:
Link Title:
Optional Image URL:
Optional Video Title:
Optional Video Embed:

Advanced Posting Options

Email Notification: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters