(800) 853-2651   Cart  View Cart    
Low Prices, Fast Shipping

 

• Tractor Parts
• Engine Kits
• Carburetors
• Manuals
• DVDs
• Hats
• Books


• Contact Us
• Shipping Rates
• Return Policy
• Ordering Help
• Company Info
• Parts Warranty
• Forums


Ferguson TO-30 Tractor Parts

[ Show Pictures ]

[Show Categories]   [Show all Ferguson Models]   [Printer Friendly]  


Brakes
Brake Pin Kit - For models TO20, TO30, TE20, 135 UK, 165 UK, 175 UK, 178, 20D, 231, 240, 240P, 240S, 35, 35X, 50F, 50H, 60H. (Part No: 1810029M91) $6.00

Brake Shoe Set - 4 brake shoes with linings bonded, for TO20, TO30, (2 wheel set). (Part No: 830537M93) $63.56

Clutch
Clutch Alignment Tool - 1-3/8" 10 spline, .67" pilot. For models TO20, TE20, TEA20, TO30, TO35. (Part No: 1112-5996) $8.49

Clutch Alignment Tool - Pilot hole 5/8, 1st stage 1 1/8, 10 spline, 2nd stage 1 3/4, 10 spline. (Part No: 1212-1600) $19.95

Clutch Alignment Tool - For dual clutch 1 1/8 10 spline and 1 5/8 10 spline. (Part No: 1712-7071) $19.95

Clutch Disc - For the following tractors using Continental Gas engine: TE20, TEA20, TO20, TO30, 202, 203, 205, 20C, 50C, with single 9" Clutch Disc, Hub is 1 3/8 inch, Splines-10, 6 springs. Replaces OEM 180241M91. (Part No: 91A7550WHD) $37.93

Clutch Kit - Includes 9" pressure plate 3 finger and 6 springs, 9" rigid clutch disc 10 spline 1-1/8" hub, release bearing, pilot bearing and clutch alignment tool. For models 135, 2135, 35, 50, MH22, MH22K, TE20, TEA20, TO20, TO30. Replaces 180263M91, 181114M91. (Part No: 1212-1610) $162.00

Clutch Kit - Includes 9" pressure plate 3 finger and 6 springs, 9" clutch disc 10 spline 1-3/8" hub, release bearing, pilot bearing and clutch alignment tool. For models 135, 2135, 35, 50, MH22, MH22K, TE20, TEA20, TO20, TO30. (Part No: 1212-6001) $162.00

Clutch Release Bearing Spring - Two used per tractor, sold individually, .627" O.D., 4.875" overall length and .095" wire diameter. For models TE20, TEA20, TO20, TO30. Replaces TO7562, 181622M1. (Part No: 9N7562) $6.10

Pilot Bearing - For models (TEA20 with 80mm or 85mm gas engine), (TO20 and TO30 with Z120 or Z129 gas engines), (TEF20 with 20C diesel engine), 20, 20E, 20F, 30, 30D, 30E, 50D, 50E. Also replaces OEM #832960M3. (Part No: 828123M1) $8.90

Pressure Plate Cover Assembly, 9 inch single - Pressure Plate Assembly - 9 inch single. (Rockford) For the following tractors using Continental Z120, Z129 or Z134 engines: MF 135, 205, 20C, 2135, 35, 50, 72, 82, F40, MH20, MH30, TO20, TO30, TO35. (Part No: 180263M91) $136.77

Release Bearing - For models 101 Jr and Sr, 135 Special, 20, 201, 202, 203, 203G, 205, 20C, 2135, 298, 303D, 303G, 35, 44, 44D, 44K, 44LP, 50, 50C, 510, 540, 550, F40, MH20, MH30, TE20, TEA20, TO20, TO30. Trans. Disc Release Bearing (greaseable). Inside Diameter is 2.0625. (Part No: 195207M1) $23.07

Cooling System
Fan Belt - FAN BELT For TE20, TO20, TO30 measures 40.25 inches x 5/8 inches. (Part No: 181636M1) $21.24

Fan Blade - 4 Blade, 15 inch diameter, 1 1/16 inch pilot hole. For Continental Gas Engine. (Part No: 181522M91-4) $44.37

Fan, 6 Blade - 15.250" dia., 1.0625" pilot hole, 1.250" bolt hole center to center. For models 150, 202, 204, 2200, 35, 50, TE20, TO20, TO30, TO35. With Continental Gas Engine. (Part No: 181522M91) $49.59

Gasket, Thermostat Body - For Tractors: TO20, TO30, TO35, MF35. (Part No: 181528M1) $1.00

Gasket, support to water pump body - Tractors: TO20, & TO30. Price is for 1 gasket. Must be ordered in quantities of 5. Minimum order is 5. (Part No: 1750296M1) $0.84

Radiator - For models TE20, TEA20, TO20, TO30, Z120, Z129, Z134 gas engines. Also replaces OEM 180291M1.Uses cap p/n 180224M91. Specify in comments section if needed. (Part No: 181623M1) $218.00

Radiator Cap - 7 lb. cap replaces 184528M1, 184528M91, 184528M1. Fits 135, 150, 165, 175, 180, 235, 240, 255, 35, 50, MH50, 65, 85, 88, TO20, TO30, TO35. (Part No: 180224M91) $9.48

Radiator Drain Tap - For models TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: 1851095M2) $3.72

Radiator Hose Kit - Contains upper hose 180085M1 and lower hose 180145M1. For models TE20, TO20, TO30, all with continental gas engines. (Part No: HK25) $17.99

Radiator Hose, Lower - For models TO20, TO30, 1.85 O.D., 1.50 I.D., 13.50 long. For 204, 205, 30, 304, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E (Part No: 180145M1) $15.38

Radiator Hose, Upper - 5-1/2" x 1-1/2". For models TE20, TO20, TO30, TO35, F40, (50, 65 with continental engine), (35, 50, with Perkins diesel), (135 with Perkins gas or diesel), (230 SN# 243032 and up), (235 with perkins diesel), 20, 2135, 50, 2500 gas Z120, Z129, Z134. (Part No: 180085M1) $5.52

Thermostat - Thermostat. For tractors: TO20, TE20, TO30. Fits in upper radiator hose, 160. 2-1/4 long for 1-1/2 I.D. hose. For TO20, TO30. Replaces OEM 181634M1. (Part No: B2NN8575A) $21.00

Water Pump Pulley - For models TE20, TO20, TO30 all with CONTINENTAL and STANDARD Engine. Pulley end 3-7/8" dia., length 2-1/2", bolt end 2-5/8", 4 bolt 1-3/4" center to center across, pilot hole 1-1/16. (Part No: 1750300M1) $43.42

Water Pump without pulley - For models TO20, TO30, TE20 with Z120 & Z129 Engines. Replaces 830862M91R, 120113N. Casting numbers P133, P113, 120K305 . (Part No: 830862M91) $38.95

Decals and Emblems
Front Hood Emblem - For models TO20, TE20, TEA20, TO30. Front Hood Emblem. Chrome with blue background 'Ferguson-Rectangle'. (Part No: R1967) $39.90

Hood Side Emblems - For TO30. Hood side emblems. Chrome Ferguson-30 . Comes in package of 2, (right and left side of hood). Requires 2 x 1/8th inch holes be drilled into hood. (Part No: R1966) $52.31

Drive Train
6 Speed Transmission Selector & Related Parts - Click on picture to view parts. ONLY parts that have a corresponding number are available. Some parts work only with specific serial number ranges within a particular tractor model. Not all parts work with this tractor model. *Do not put this part in basket. You must call for application, identification and availability. NOTE

Axle Bearing Assembly - 2.00" I.D. For models TE20, TEA20, TEF20, TO20, TO30. Assembly includes Cup(3720) and Cone(3795). Replaces 195162M1. (Part No: S.18516) $55.52

Axle Collar - For models TO20, TEA20, TEF20, TED20, TO30. Replaces 181257M1. (Part No: 9N4132) $15.28

Bearing Cup - Double tapered cup (53376D) for differential. For tractors: TE20, TO20, TO30, TO35 prior to SN# 169467 MF35, MF50 using sleeve no. 181251M91 also MF65 to SN# CL2686121 MF135, MF150, MF165, MF175, MF180. (Part No: 181251DTC) $85.66

Bearing Cup, Differential - For models FE35, TE20, TO20, TO30, 135, 150, 165, 175, 180, 20, 20C, 20D, 20F, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 24, 240, 240P, 245, 25, 250, 2500, 253, 255, 265, 270, 275, 282, 285, 30, 30B, 30D, 30E, 30H, 302, 31, 3165, 356, 360, 362, 3630, 3650, 375, 383, 390, 390T, 399, 40, 40B, 40E, 4500, 50, 50A, 50C, 50D, 50E, 50H, 60, 60H, 60HT, 65, 6500, 670, TO35 SN# <-169467. Replaces 1850090M91. (Part No: 185778M1) $26.02

Bearing Cup, Rear Axle, LH Inner - LH Bearing Cup - Rear Axle Inner for MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF35, MF50, MF65, TO20, TO30, TO35 (Part No: 195160M1) $19.28

Differential Bearing & Cup - Fits in differential lock.For models MF135, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF35, MF65, TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: 195159M1) $23.25

Gasket, Rear Axle Trumpet Housing - Size is approx 15-1/4" Fits: TEA20, TO20, TO30, TO35, 135, 150, 165, 175, 180, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 2500, 30, 31, 3165, 35, 40, 50, 50, 65.Minimum quantity order is 2, priced each. (Part No: 183254M1) $2.98

Gear Shift Boot - For models TE20, TO20, TO30, TO35, 35, 50, 65, 85, 88, Super 90, 135, 150, 165, 175, 230, 235, 245, 255, 265, 275, 285. Top Hole 1/2 inch Bottom hole 1 1/2 inch (Part No: 520858M1) $4.58

Gear Shift Knob - Round ball, 3/8" NF thread. For models TO20, TE20, TEA20, TEF20, TO30, TO35, FE35, F40, 130, 135, 150, 165, 175, 20, 202, 203, 204, 205, 2135, 220, 2200, 2500, 30, 302, 303, 304, 30E, 3165, 320, 333, 35, 356, 40, 404, 406, 44, 444, 50, 50A, 50E, 555, 65, 85, 88, 90, Super 90, 95, 98, F40, FE135, MH50, TO35. **MUST ORDER IN QTY OF 2, Priced Each** (Part No: 180006M91) $4.70

Oil Seal, Rear Axle, Inner - OIL SEAL For TO30, TO20, TEF20, TED20, TEA20. This is an inner oil seal for the rear axle. Measures 2" x 2 7/8" x 1/2". (Part No: 195555M1) $9.60

Oil Seal, Rear Axle, Outer - 2-3/8" I.D, 3-1/2" O.D, 5/8" thick. For models TO20, TO30, TEF20, TED20, TEA20. This is an outer oil seal for the rear axle. Replaces 890640M1. (Part No: 195557M1) $6.04

Rear Axle Housing Gasket, Outer - For models TO20, TO30, TO35. Replaces 181232M1. Thickness 0.016" Price is for each. (Part No: 9N4130) $0.98

Rear Axle Seals & Collar Kit - Contains: outer axle seal, shrink on collar & inner axle seal. Kit is for 1 axle, 2 required per tractor. For models TE20, TEA20, TEF20, TO20, TO30. (Part No: S.42078) $31.59

Transmission Fill Plug - For models TE20, TEA20, TO20, TO30, 35, 40, 50, 135, 231, 240, 250 2135. Also replaces 768300M1 and 3799441M2. Plug has a 2.3125 O.D. Flange. (Part No: 180580M1) $12.00

Electrical System
12 Volt Conversion Kit - 12 Volt Conversion For TO30 ONLY. (Includes alternator with built-in regulator, 12 volt resistor, wiring harness, brackets and instructions) (Part No: TO30ALT12V) $154.99

Alternator Base Bracket - Base bracket used in 12 volt conversion kit. For model TO30. Hardware kit available as p/n HDW9302. (Part No: GFD9309) $13.50

Alternator Hardware Kit - Hardware for brackets in 12 volt conversion kits. For models TO20, TO30. (Part No: HDW9302) $4.50

Alternator Top Bracket - Adjustable top bracket used in 12 volt conversion kit. For model TO30. Hardware kit available as p/n HDW9302. (Part No: GFD9310) $11.95

Battery Cable - Cable, starter switch to starter. Tractors: TO20, TO30. 16" long. (Part No: 180099M91) $13.66

Battery Cable - Cable, battery to switch. For tractors: TE20, TO20, TO30 battery to ground for tractors: MF85, 88 gas. 21 long, 2 gauge. For 204, 205, 30, 304, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E. Replaces OEM 180166M92. (Part No: 9N14300C) $13.47

Battery Cable Ground Strap - For: TE20, TO20, TO30, TO35. 5-1/2 long. Replaces 180165M91. (Part No: D1NN14301H) $11.82

Coil, Ignition 6V - Coil for Delco distributor with clip held cap. For 202, 204, 20, 26, 27L, 27, 302, 303, 304, 34, 356, 35, 402, 404, 60, 70, 72, 80, 82, 90, 92, MF35, MF50, MF65, MF85, MF88, MH50, Super 92, Super 90, TO20, TO30, TO35. Replaces 1024481M91. (Part No: D4PE12029AA) $19.95

Control Box, 12 Volt - For tractors with generator and Standard engines. Replaces OEM: 829951M91, 1050840M91. For models 20E, 240, 275UK, 283UK, 290UK and TE20, TEA20, TO20, TO30, TO35. (Part No: 1890130M91) $47.20

Distributor - For models TO20, TO30, TO35, 35 (to SN# 245932), F40, 50 to SN# 536248. Replaces 1111722, 1111740, (MF 181686M91), 1112570, 1112586. This is a distributor with points. If converting this distributor to a Point-less Electronic Ignition use part #1244A with this distributor. (Part No: 182852M91-TP) $377.22

Distributor Cap 4 Cylinder - Fits: TO20, TO30, TO35, 35, 202, 204, 302, 304, 50, 65, 85, 88, Super 90. Clip Type Cap For Delco Distributors: Replaces 811735 Delco and 1750411M1. (Part No: 1750411M91) $9.60

Dust Cover - Dust cover for Delco distributor with clip held cap. For 202, 204, 302, 304, 34, 35, 356, 92, MF35, MF50, MF65, MF85, MF88, Super 92, Super 90, TO20, TO30, TO35. Replaces 1750491M91. (Part No: 1900119) $9.90

Electronic Ignition Conversion Kit, 12 volt negative ground - Fits TO20, TO30, TO35, 50, MH50, 65 : - For TO20 with Continental Z120 engine and Delco distributor. TO30 with Continental Z129 engine and Delco 1111740 distributor, TO35 and MH50 with Continental. Z129 or Z134with Delco distibutor 1112557 or 1112570, TO35, 35 and 50 with Continental Z134 and a Delco 1112570, 1112585 or 1112385 distibutor, 65 with Continental G176 engine and a Delco 1112583 or 1112589 distributor. Electronic ignition conversion kit. Replaces points and condenser with an electronic module. For counter clockwise distributors with clip type cap. For use on 12 volt negative ground system only. Never change points again. Easy to install. Increases spark plug life. Increases horsepower. Improves fuel economy. Solid-state electronics. (Part No: 1143) $83.12

Electronic Ignition Conversion Kit, 6 volt positive ground - For TO20 with Continental Z120 engine and Delco distributor including Delco distributor 1112618. TO30 with Continental Z129 engine and Delco 1111740 distributor, TO35 and MH50, 50 with Continental. Z129 or Z134with Delco distibutor 1112557, 1111722 or 1112570, TO35, 35 and 50 with Continental Z134 and a Delco 1112570, 1112585 or 1112385 distibutor, 65 with Continental G176 engine and a Delco 1112583 or 1112589 distributor. Electronic ignition conversion kit. Replaces points and condenser with an electronic module. For counter clockwise distributors with clip type cap. For use on 6 volt positive ground system only. Never change points again. Easy to install. Increases spark plug life. Increases horsepower. Improves fuel economy. Solid-state electronics. (Part No: 1143P6) $91.48

Generator Shield - For Models: TO20, TE20, TO30, TE30. (Part No: 892639M92) $21.15

Generator, 6 Volt, Rebuilt - Pulley not included. For models TO30, TO35 1951-1955. Add $35.00 core charge to price - this charge is refundable if you send your core to us. (Part No: 1100523) $251.21

Hand Crank, Starter - For models TE20, TO20, TO30. (Part No: 180890M1) $21.20

Ignition Kit, Delco Clip-Held Cap Distributor - Ignition kit For Delco distributor with CLIP held cap. Contains points, condenser, rotor, and proper point gap gauge. Fits: 202, 204, 302, 304, 34, 35, 356, 92, MF35, MF50, MF65, MF85, MF88, Super 92, Super 90, TO20, TO30, TO35. (Part No: ATK1DCR) $11.98

Ignition Tune Up Kit, With Plugs - FOR DELCO DISTRIBUTOR WITH CLIP-HELD CAP. 4 Cylinder kit includes spark plugs, points, condenser, and rotor. For models with clip held Type Delco Distributor Caps: TO20, TO30, TO35, MF35(With SN# prior to 245033), MH50(With SN# Prior to 536249), MF50(With SN# prior to 536249), MF65(With SN# prior to 702825), MF85, MF88, MF90 Super, 35 Util(with SN# prior to 655001052), 35 Turf(with SN# prior to 656000452), 202(with SN# prior to 308962), 204(with SN# prior to 343688), 302(with SN# prior to 119700082), 304 (with SN# prior to 119750053), 356(with SN# prior to 570001025), Super 92. (Part No: MFITK10) $23.56

Resistor - Ballast resistor used for coil in ignition system. Resistance = .6 ohms. Note: This is NOT used on all ignition systems. (Part No: 8NE10306) $4.95

Rotor - Used with Delco distributor and clip held cap. For models (35 up to SN# 245033), (50 up to SN# 536249), (65 up to SN# 702826), TO20, TO30, TO35. (Part No: 1750498M1) $4.99

Spark Plug - Price shown is for EACH, shipped in lots of 4. Enter '4' in QTY box. Fits Continental gas engines in: TO20, TO30, TO35, 50, 65, 85, 88, S90, 135, 150, 165, 175, 180, 1100, 230, 235. Gas Industrials: MF35 Utility & turf, 202, 204, 302, 304. Massey Harris: Pony, 21, 22, 23, 30, 33, 44, 44-6, 44 Special, 101Jr. 333, 444, 555, 303, 402, 404. Priced EACH, minimum Qty is 4. (Part No: AL386) $3.24

Spark Plug Wire Set, Custom - No cutting or fitting required for these stainless steel/kevlar wires. These are custom made for the following 4-cylinder Continental Gas engines using Delco distributors: Z120, Z129, Z134, and Z145. Used on tractors: TE20, TO20, TO30, F40, 135, 135 Deluxe, 150, 35, 50, MH50, TO35. Also used on INDUSTRIALS: 202, 204. (Part No: S.42779) $15.98

Starter Drive - Drive assembly attaches with keyway and set screws. For tractors: TO20, TO30, TO35. Services Delco starter 1109457, 1107654. (Part No: 1035335M91) $62.29

Starter Nose Cone - VERIFY BOLT PATTERN - THIS NOSE CONE USES 2 BOLTS TO MOUNT TO THE STARTER BODY. If you have a 4 bolt, we do not have a replacement. Can fit OEM starters only 181541M91/1109457, 182454M92/1107654, 190004M91/1107226 For models TO20, TO30, TO35, F40, MH50, 50, 65, Early 302, 304, 356. Replaces Delco # 1934316. Will NOT fit 4858MFGXL aftermarket starter. (Part No: 1751902M91) $56.63

Starter Switch - Switch assembly with key, for ignition and light. Switch has 3 terminals. For GAS tractors: TE20, TEA20, TO20, TO30, TO35, MF35, MF50, MF65. (Part No: 180681M93) $21.58

Starter Switch, Manual - For TO20, TO30. Manual Starter Switch. (Part No: 181679M1) $12.74

Starter, 12 Volt - 12 Volt version of our 4858MFGXL starter. For Models: TO20, TO30, TO35, F40, MH50, 50, 65, Early 302, 304, 356. Has 9 tooth gear on bendix. Single bolted stud on rear side of starter (about 2" from the end) for electrical connection. Overall length is 12.5 inches, Diameter is 4 inches, 2 bolt center-to-center is 4.25 inches. Can replace OEM starters 181541M91, 1109457, 182454M92, 1107654, 190004M91, 1107226 and TISCO starters 7877-EX, 81271-EX, 85451-EX. 1 YR warranty. (Part No: 4858MFGXL_12V) $179.95

Starter, 6 Volt ONLY, Continental GAS Engine - STARTER ASSEMBLY FOR 6 VOLT SYSTEMS ONLY with Continental Gas engine.For TO20, TO30, TO35, F40, MH50, 50, 65, Early 302, 304, 356. Has 9 tooth gear on bendix. Single bolted stud on rear side of starter (about 2" from the end) for electrical connection. Overall length is 12.5 inches, Diameter is 4 inches, 2 bolt center-to-center is 4.25 inches. Can replace OEM starters 181541M91, 1109457, 182454M92, 1107654, 190004M91, 1107226 and TISCO starters 7877-EX, 81271-EX, 85451-EX. 1 YR warranty. This starter is for the ring gear being on the rear of the flywheel. If your ring gear is on the front of the flywheel, you need the Lucas type starter (see TE20, part #829853M91). Measurement from the outer bolt flange to the end of nose cone is 3.274 inches. NO RETURNS ALLOWED IF NOSE CONE IS BROKEN. The only reason a starter nose will break is due to: Bent Armature Shaft, Ignition Timing is Incorrect, Improper Drive-to-ring-gear clearance, or defective electrical causing engine kick back. (Part No: 4858MFGXL) $159.90

Tune Kit Tisco Distributor - For Tisco Distributor 182852M91-TIS supplied since February 1987. Kit includes Cap, Rotor, condenser and Point Set. (Part No: MFDISTKITA) $21.48

Tune Up Kit, Comprehensive - FOR DELCO DISTRIBUTOR WITH CLIP-HELD CAP. For 4-cylinder gas engine, kit includes Spark Plugs, Universal Plug Wires, Points, Condenser, Rotor, Distributor Cap. Fits tractors: TO20, TO30, TO35, 35 Ag. before SN# 245033, 35 Utility before SN# 655001052, 35 Turf before SN# 65600452, 85, 88, 90 Super, MH & 50 before SN# 536249, 65 before SN# 702825, 202 Ind. before SN# 308962, 204 Ind. before SN# 343688, 302 Ind. before SN# 119750053, 356 Ind. before SN# 570001025, Swathers 34, 44:combines 92, Super 92. (Part No: MFTUNEKIT) $39.17

Voltage Regulator, 6 Volt, Positive Ground - For models TO20, TO30, TO35. Voltage Regulator 6 Volt. replaces 180142M92. 4 connectors, 3 on one side, 1 on the other. (Part No: GDR6003) $24.95

Wiring Harness, 12 Volt Conversion Kit - Wiring harness for 12 volt conversion kits. For models TO20, TO30. (Part No: AKT9205) $15.00

Wiring Harness, Main - Restoration quality, 6 Volt generator systems only. Cotton braided, exactly like original. Includes headlight, wires and wiring instructions. All terminals soldered and sealed. For model TO30. (Part No: 181699M91) $198.00

Engine Bearings
Cam Bearing Set - For TO30 with Z129 engine. (Part No: SH-683S) $56.16

Main Bearing Kit, Standard - Main bearing kit (flanged front main bearing), Standard, for Continental gasoline engines Z120 and Z129. Tractors: TE20, TO20, TO30. Complete for one engine. Available in Standard or.010", .020", .030 undersize. Specify size in comments section of order form when ordering (Part No: 830511FL-X) $169.95

Main Bearing Set -.040 - For Z120 & Z129 Gas Engine. Main bearing kit size is.040". For TE20, TO20, TO30. (Part No: s.60900) $37.88

Main Bearing Set, .010 - For Z120 & Z129 Gas Engine. Main bearing kit size is.010. For TE20, TO20, TO30.FLANGED TYPE BEARING SET ARE NO LONGER AVAILABLE, THEY HAVE BEEN REPLACED BY SHELL TYPE WITH THRUST WASHERS. (Part No: MS-260P-010) $107.11

Main Bearing Set, .020 - For Z120 & Z129 Gas Engine. Main bearing kit size is.020. For TE20, TO20, TO30.FLANGED TYPE BEARING SET ARE NO LONGER AVAILABLE, THEY HAVE BEEN REPLACED BY SHELL TYPE WITH THRUST WASHERS. (Part No: MS-260P-020) $107.11

Main Bearing Set, Standard - For Z120 & Z129 Gas Engine. Main bearing kit size is Standard. For TE20, TO20, TO30. FLANGED TYPE BEARING SET ARE NO LONGER AVAILABLE, THEY HAVE BEEN REPLACED BY SHELL TYPE WITH THRUST WASHERS. (Part No: MS-260P-STD) $107.11

Rod Bearing -.040 - SINGLE bearing.040" undersize, for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Special Order - Non-refundable. Minimum order qty is 4. (Part No: 1670SB40) $22.44

Rod Bearing Set, .002 - Connecting rod bearing kit, .002" undersize, for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Part No: 830508M91) $65.49

Rod Bearing Set, .010 - Connecting rod bearing kit, .010" undersize, for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Part No: 830509M91) $38.37

Rod Bearing Set, .020 - Connecting rod bearing kit, .020" undersize, for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Part No: 830510M91) $35.92

Rod Bearing Set, .030 - Connecting rod bearing kit, .030" undersize, for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Part No: 830510-030) $43.90

Rod Bearing Set, Standard - Standard connecting rod bearing kit for Continental gasoline engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Part No: 830486M91) $37.88

Rod Bushing, SINGLE - Fits Z129 Continental Gas Engine. SINGLE rod bushing. ** Order 840708M91 for complete set of 4. (Part No: 760916M1) $3.21

Engine Gaskets
Crank Seal, Front - Lip-type. Fits Four Cylinder Continental Gas engines. For 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35 (Part No: 15287A) $12.30

Crank Seal, Rear - Lip-type. Fits Four Cylinder Continental engines. For 135, 202, 204, F40, MF135, MF150, MF165, MF35, MF50, MF65, MH50, TE20, TO20, TO30, TO35 (Part No: 1750216M92) $14.58

Crankshaft Seal Kit - Kit contains front & rear crank lip-type seals and gasket for rear and felt seal for front. For continental gas engines: Z120, Z129, Z134, Z145. Tractor Models: TO20, TE20, TO30, TO35, F40, MF50, MF35, MF135, MF150, 202, 204 (Part No: VPC5122) $28.66

Full Gasket Set With Seals - For TE20, TO20 with Continental Z120 and TO30 with Continental Z129. Comes with crankshaft seals (Part No: FS1865) $60.12

Full Gasket Set Without Crankshaft Seals - Complete engine gasket set less crankshaft and piston sleeve seals for Continental gasoline engines Z120 & Z129 Tractors: TE20, TO20, TO30. ** Cylinder Sleeve seals, sold in Quantity of 2, available as p/n 1750000M1. (Part No: 830631M91) $42.15

Head Gasket - Gasket, cylinder head. For models TE20, TO20, TO30 all with either Continental Z120 or Z129 engines. (Part No: 1750336M1) $24.30

Head Gasket Set - For Continental gasoline engines Z120 & Z129. Tractors: TE20, TO20, TO30. (Upper gasket set with head gasket). (Part No: TO20VG) $34.35

Oil Pan Gasket - For models TE20, TO20, TO30, TO35, F40. (Part No: 1750024M1) $6.84

Rocker Cover Gasket - For models TE20, TO20, TO30, TO35, F40. All using Continental Z120, Z129 or Z134 gas engines. (Part No: 1750002M1) $8.62

Engine Rebuild Kits
In-Frame Overhaul Kit - 3 3/8 Overbore For TO30 with Continental Z129. Contains Pistons, rings, pins and retainers, piston sleeves, head gasket set, oil pan gasket set, rod bearings, main bearings. (Part No: R1995-IFKA) $429.06

Overhaul Kit - Made by TISCO. Engine Overhaul Kit For TO30 (Z129 Continental Gas) Contains Sleeve & Piston Kit (sleeves, pistons, rings, pins & retainers, Super Power Kit, increases bore to 3-3/8"). Pin Bushings. Complete Gasket Set. Connecting Rod Bearing Kit. Main Bearing Kit.PIN TYPE Intake & KEY TYPE Exhaust Valves (plus guides, locks and springs). Valve Stem Seal. Available with Std., .010, .020, or.030 bearings. (Part No: EOK119FL) $513.50

Overhaul Kit, Comprehensive - Made by TISCO. For TO30 with Continental Z129 engine, overbore to 3 3/8". Pin type intake, key type exhaust valves. Carburetor kit is for Marvel-Schebler. Bearing sizes available in kit are standard or.010. FLANGED TYPE BEARING SET ARE NO LONGER AVAILABLE, THEY HAVE BEEN REPLACED BY SHELL TYPE WITH THRUST WASHERS. Overhaul Kit, Comprehensive includes: Sleeve, piston and ring kit, Complete overhaul gasket set including crank seals, Connecting rod bearings, Main bearings, Pin bushings, Exhaust valves, Intake valves, Valve guides, Valve springs, Valve keys, Fan belt, Oil pump repair kit, Oil filter element, Air cleaner hose, Radiator hoses upper and lower, Distributor points, Distributor condenser, Spark plugs and Basic carburetor kit. Specify when ordering rod and main bearing sizes in comments section of order form. (Part No: 30K600) $635.08

Overhaul Kit, Comprehensive, Less Bearings - Made by TISCO. 4-Cylinder Continental Gas, 129 CID. 3-1/4" Standard Bore, 3-3/8" Overbore Supplied. Complete Engine Overhaul Kit, less bearings. Contains sleeves & sleeve seals, pistons & rings, complete gasket set including crank seals, pin bushings, intake & exhaust valves, valve guides, springs, keys, fan belt, oil pump kit, oil filter element, air cleaner hose, upper & lower radiator hoses, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. For TO30 Series. (Part No: 30K600-LCB) $535.25

Overhaul Kit, Less Bearings - Made by TISCO. For models TO30. This kit is a overbore to 3-3/8 for Z129 Continental gas engine. Kit contains, sleeves, sleeve seals, pistons and rings, pins and retainers, pin bushings, gasket set and crankshaft seals. Engine bearings ordered separately. (Part No: BEKM119FL-LCB) $291.62

Overhaul Kit, Z129 Gas, Less Bearings, With Valves - Made by TISCO. Engine Overhaul Kit For TO30 (Z129 Continental Gas) Contains Sleeve & Piston Kit (sleeves, pistons, rings, pins & retainers, Super Power Kit, increases bore to 3 3/8 inch). Pin Bushings. Complete Gasket Set. PIN TYPE Intake & KEY TYPE Exhaust Valves (plus guides, locks and springs). Valve Stem Seal. Bearings sold separtely. (Part No: EOK119FL-LCB) $399.38

Overhaul Kit, Z129 Gas, With bearings, Less Valves - Overbore 3-3/8". Kit includes - Pistons, Piston Rings, Liners, Main & Con Rod Bearings, Top & Bottom Gasket Sets, Front & Rear Seals. Main & Rod Bearings are available in std, .010, .020, .030, Specify in 'COMMENTS' section which size you need. For model TO30 with Z129 continental engine. (Part No: EKM131) $384.75

Valve Overhaul Kit, Z129 or Z134 Engines - Made by TISCO. For TO30, TO35, 35, F40, MH50, 50, 135 Special, all with 4 cylinder Z129 or Z134 Continental Engine. Engine Valve Overhaul Kit includes Pin type Intake and Key Type Exhaust Valves, valve springs, valve keys and valve guides. (Part No: VOKM129) $104.30

Engine Parts
Camshaft - For Z120, Z129, or Z134 Continental engines on TE20, TO20, TO30, TO35, 135, 202, 204, 2135, 2200, 30, 35, 50. Also replaces 836543M1. (Part No: 836543M91) $150.19

Camshaft Gear - Camshaft gear, 48 teeth, Continental gas engine in models: TE20, TO20, TO30, TO35, F40, MH50, 50, 135, 150; Industrials: 202, 204, 2135. (Part No: 1750237M1) $94.07

Connecting Rod, Reconditioned - With pin bushing. Fits Z120, Z129 and Z134 Gas engines in: TE20, TO20, TO30, TO35, 35, 50, 135, 150, 202, 203, 204, 235, 245. (Part No: R1201623) $113.92

Crankshaft - New Crankshaft Only (Bearings not included) for Continental Z129 and Z134 gas engines. For TO30, TO35, 35, 50, MH50, 135, 202, 204 . See our Engine Bearings category for prices and sizes. Also replaces 1750169M1. (Part No: 830686M91) $358.56

Crankshaft Gear - Crankshaft gear, 24 teeth: TE20, TO20, TO30. Continental gas engine. (Part No: 1750284M1) $40.62

Exhaust Valve Stem Cap, Aftermarket - Package of 4 for caps on Z120, Z129 and Z134 engines in models TO20, TO30, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. (Part No: 830705M91) $24.50

Exhaust Valve Stem Cap, OEM - These are original equipment, NOT aftermarket. Package of 4 for caps on Z120, Z129 and Z134 engines in models TO20, TO30, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. (Part No: 830705M91-OE) $51.84

Exhaust Valve Stem Lash Cap - .499" diameter, 0.235" tall, 0.126" stem diameter. For models (TO20 Without Rotators), TO35, TO30, 135, 150, 202, 204, 230, 235, 245, 2135, 2500, 4500, 20C, 30B, 35, 50, F40 and Massey Harris 50 all with 4 cylinder Continental gas/LP Engines). Replaces: Z129I-206. (Part No: 1750071M1) $10.38

Exhaust Valve, Z129 & Z134 Engines - Exhaust valve, key-type. For 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. Must order in quantities of 4, price is for 1. (Part No: 1750072M1) $16.56

Flywheel Ring Gear, Continental Gas - For models TE20, TO20, TO30, TO35, 35, 50, 65, 135, 150, 165, 175, 180, all with Continental Gas Engine. Flywheel Ring Gear with 145 Teeth. (Part No: 1750034M1) $32.46

Governor Assembly - For Continental engines in tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF150, Pony, 202, 204, 2135, 2200, 2500. Also fits: MF135, MF150, with Perkins gas. Replaces 1002849M91. (Part No: 529737M1) $191.17

Governor Compensating Spring - Fits the following tractors using Continental gas engine: TO20, TE20, TO30, TO35, F40, MF 35, 50, 135. INDUSTRIALS: 2135 (Part No: 181535M1) $6.95

Governor Shaft Seal - For models TO20, TO30, TO35, 135, 150, 230, 235, 245, 35, 50. (Part No: 1750108M1) $8.12

Intake Valve Stem Cap, Aftermarket - Package of 4. For Z120, Z129 and Z134 engines. (Part No: 830704M91) $24.50

Intake Valve Stem Cap, OEM - These are original equipment, NOT aftermarket. Package of 4. For Z120, Z129 and Z134 engines. (Part No: 830704M91-OE) $56.84

Intake Valve Stem Lash Cap - .500" O.D., 0.218" tall, 0.316" I.D. For models (TO20 Without Rotators), TO35, TO30, 135, 150, 202, 204, 230, 235, 245, 2135, 2500, 4500, 20C, 30B, 35, 50, F40 and Massey Harris 50 all with 4 cylinder Continental gas/LP Engines). Replaces: Z120I-208. (Part No: 1750060M1) $10.38

Intake Valve, Z129 & Z134 Engines - Intake valve, pin-type. For 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. Price is for EACH. Minimum Order is 4. (Part No: 1750070M1) $12.86

Lifter, Refaced - Single lifter fits Z120, Z129 and Z134 gas engines in TO20, TO30, TO35, 35, 50, 135, 150, 165, 175. (Part No: 1750111M1) $14.40

Piston Pin Bushing Set - Bushing kit, 4-760916M1 pin bushings. For 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35 all with continental gas engines. (Part No: 840708M91) $16.70

Push Rod - For Continental Z120, Z129, Z134, Z145 gas/LP engines in models TE20, TO20, TO30, 35, F40, 50, 135, 150, 202, 204, 230, 235, 245, 30C, 30B, 2135, 2200, 2500, 4500. Sold in singles, Priced each. (Part No: MFS2420) $22.50

Rocker Arm Assembly - For Continental Z120, Z129, Z134, Z145 gas engines in models TE20, TO20, TO30, 35, F40, 50, 135, 150, 202, 204, 230, 235, 245, 30C, 30B, 2135, 2200, 2500, 4500. With Forged ends. (Part No: MFS129) $224.95

Rocker Shaft Bushing - Set of 8, Semi finished. For models TE20, TO20, TO30, 135 Deluxe, 150 with Continental Z120, Z129, Z134 or Z145 gas engines. (Part No: S.60327) $31.13

Valve Guide Set - Z134, Z129 or Z120 Gas - Guide set. 8 guides. For 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35 all with Z134, Z129 or Z120 gas engines. (Part No: 830490M91) $20.82

Valve Lock, Pin Type - Intake and exhaust valve lock, 1 used per valve, sold in quantities of 4, price shown is for 1. For models TE20, TO20, TO30, F40, MF135, MF35, MF50, TO35, 202, 204 all with Z134, Z129 or Z120 gas engines with pin type valves. (Part No: 18291A) $1.38

Valve Service Kit - For models 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TO30, TO35. Fits Continental Z129 engine. Contains: springs, guides, locks, (no valves). (Part No: VSKM129) $39.53

Valve Spring Kit - Set of 8 springs, intake & exhaust. For Continental Gas Engines in Models: 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35. (Part No: 840754M91) $18.90

Engine Pistons and Sleeves
O-Ring Seal, Piston Liner - SINGLE O-ring for piston Liner on Continental Z120, Z129 and Z134 engines (NOTE: Liners usually use a minimum of 2 O-rings each). Used on: TE20, TO20, TO30, TO35, F40. (Part No: S.11364) $1.94

Piston - Single piston 3-3/8" overbore used on continental Z129, Z134 gas engines. For models TO30, TO35, F40. (Part No: S.60839) $28.24

Piston & Sleeve Kit, Continental Engine - Complete kit for 4 cylinders. For TO30, TO35, 35, F40, MH50, 50, 135, (Z129, Z134 Continental Gas) Contains Sleeves, Sleeve Seals, Pistons & Rings, Pins and Retainers. 3-3/8" Overbore. (Part No: PK105) $266.10

Piston Sleeve - Single sleeve for 3-3/8" overbore piston used on Continental Z129, Z134 gas engines. For models TO30, TO35, F40. (Part No: S.60844) $26.88

Piston and Liner Kit, Continental Engine - For ONE cylinder, 3 3/8 inch bore. Includes: Piston, Liner, rings. For models 135, 202, 204, 35, 50, F40, TO30, TO35. All with continental Z129, Z134 gas engine. (Part No: SK105) $72.51

Engine Rings
Piston Ring Set - Ring set for 4 pistons. For 3-3/8" overbore pistons. (3 compression 3/32, 1 oil 3/16). For models 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. (Part No: PRS105) $43.68

Piston Ring Set 3 1/4 Bore - For 4 ring piston, 3 1/4 Bore, 2 compression at 3/32 and 2 Oil at 5/32. Complete set for 4 cylinder gas engine. (Part No: 2C7582) $105.92

Piston Ring Set, Std. - For model TO30 with Z129. Original 3 1/4 inch bore, 3 compressing rings 1/8 inch and one oil ring 3/16 inch. 1 Used per engine. (Part No: 836096M91) $57.81

Exhaust System
Exhaust Elbow - Fits the following tractors using Continental Z120, Z129, or Z134 GAS engines: TE20, TO20, TO30, TO35. Dimension 'A' = 1-7/8" (Part No: 181886M2) $32.00

Exhaust Pipe - Horizontal - For gas engine on TO20 & TO30. Has Flared inlet, 18" vertical length, 23" horizontal length, 1 1/2" Outlet O.D.. For HORIZONTAL exhaust. (Part No: 181460M1) $24.45

Exhaust Pipe Horizontal - For 35 and TO30 with Gas engine. L-shaped configuration, 3 bolt inlet flange, 18 inch vertical length, 20 inch horizontal lenth, 1.5 inch outlet diameter. Also replaces 181600M91 (Part No: 181600M92) $29.93

Manifold - Intake & Exhaust Manifold For TE20, TO20, TO30, TO35, 135 all with 4 Cylinder Continental Gas Engines. Will also work on the 50 with slight modification to exhaust pipe. Includes adapter, and gaskets (R0059G). Replaces 1040903M91, 1039258M1, 105342M91, 1046679M1. Comes with Gasket set. Does not come with hardware, i.e. bolts, nuts, etc. Optional clamp kit used on TO20 and TO30 with flared pipe end available as part # FP185, specify in COMMENTS when ordering, if needed. (Part No: 1750343M91) $144.90

Manifold Gasket Set - For TE20, TO20, TO30, TO35, 35, 135 all with Continental Gas Engine. (Part No: R0059G) $8.00

Muffler - Horizontal muffler (round). For MF135, MF35, TO20, TO30, TO35 Inlet I.D. 1.5 inches Outlet O.D. 1.5 inches Length 34 inches, Shell Diameter 3.25 inches, inlet length 2.75 inches, outlet length 11 inches. (Part No: 505545M92) $44.62

Muffler - Vertical 2 piece assembly. Manifold end is flared. No support bracket. For tractor: TE20, TO20, TO30 2-piece. For TE20, TO20, TO30 (Part No: M112) $50.62

Muffler - 2 1/2" INLET LENGTH, 1 1/2" INLET I.D., 23" SHELL LENGTH, 8 1/2" OUTLET LENGTH, 1 1/2" OUTLET O.D., 34" OVERALL LENGTH. NOTE : Horizontal / Round Body has 3 1/4" Shell Diameter. For models 135, 35, TE20, TO20, T030, TO35 all with gas or diesel engine. (Part No: 180364M91) $37.23

Muffler Clamp - Flanged clamp. For models TO20, TO30, TE20. Replaces 181461M91. (Part No: FP185) $6.15

Muffler and Pipe - Vertical Exhaust One Piece muffler and pipe. Flared inlet. 1 Piece. Outlet O.D. - 1 1/2 For TO20, TO30 Gas. Support Bracket attached. Use FP185 Clamp, Use R1798 Rain Cap. (Part No: R1693) $43.77

Muffler and Pipe Assembly - Horizontal Muffler & pipe assembly. For tractors: TO20, TO30 replaces 505545M92 muffler & 180460M1 pipe. (Part No: M500) $53.19

Muffler and Pipe, Vertical - Two piece kit includes muffler and pipe, inlet is flared. 10-1/2" muffler shell, 3-1/4" shell dia., 17-1/2" pipe length, 1-1/2" outlet dia. For models TO20, TO30 all with gas engine from 1948-1957. (Part No: MF1810) $51.27

Muffler, Vertical, Black Enamel - Comes with pipe, 2 clamps, bolts and rain cap, 1-7/8" inlet. For models TO35 with continental engine., (TO20, TE20, TO30 if manifold S.60036, elbow s.43369 and gasket s.40645 are used. Replaces 181867M91. (Part No: S.43643) $64.03

Muffler, Vertical, Silver - Comes with pipe, 2 clamps, bolts and rain cap, 1-7/8" inlet. For models TO35 with continental engine., (TO20, TE20, TO30 if manifold S.60036, elbow s.43369 and gasket s.40645 are used. Replaces 181867M91. (Part No: S.43644) $57.42

Vertical Muffler Pipe to Manifold Gasket - For models TE20, TO20, TO30, TO35, 135, 150. Also Replaces OEM # 827877M1. Vertical Muffler with Pipe. ** Minimum order quantity is 2, Priced each. (Part No: 3640488M1) $2.43

Fuel System / Air Intake
Air Cleaner Hose - For models TO30, TO35, (TEA20 with 85mm engine SN# 200001 and up). Measures 1 9/16 inches I.D. small end, 3 inches I.D. large end, Overall length of 6 1/2 inches. (Part No: 180362M1) $23.80

Air Hose to Carburetor - For TE20, TO20, TO30, 35, 50, 135, MH50 gas tractors. Rubber Air Hose is 2 3/8 inches long, 1 1/2 inch inside diameter. (Part No: 9N9652) $2.72

Carburetor Float - Float for Marvel-Schebler small bowl carburetors in tractors: TO20, TO30, TO35, MF35, F40, MH50, MF135, MF150. For F40, MF135, MF150, MF35, TO20, TO30, TO35. Replaces 15480A. (Part No: 9N9550A) $11.80

Carburetor Kit, Basic - Kit for Marvel TSX882, TSX34, TSX308, TSX309, TSX683, TSX361, TSX248, TSX272, TSX312, TSX605, TSX458 carbs used on 135, 150, 20, 30, 35, 50, TE20, TO20, TO30. (Part No: MS101) $22.94

Carburetor Kit, Basic - Fits Zenith carburetors 13339, 11532, 13876, 13863, 13714, 12708, 14987, 12825. For models TO20, TO30, MH81, MH82, 3D combines, 60PT combines, MH30, MH33, MH81, MH82, MH101JR, MH102JR, MH201, MH203, MH333. (Part No: K2119) $25.86

Carburetor Kit, Comprehensive - For models TO20, TO30 all with Marvel Schebler Carburetor - TSX458. Comprehensive Carburetor Kit contains the following parts for a Major Overhaul. Includes: gaskets, needles, seats, throttle shaft, springs, and mixture screw. The main nozzle that is in this kit will NOT fit the TSX458. Does not include float. (Part No: C549V) $31.13

Carburetor, New - New Zenith Carburetor with reversible linkage. These carburetors outperform the original carbs used on: TO20, TO30, 16, 81, 82, 3D Combines, 60 PT Combines, & Industrals using Continental 140, F162 gas engines. Also fits Massey Harris: 30, MH33, 81, 82 101JR, 102JR, 201, 203, 333 (F162 engines). Replaces Marvel-Schebler TSX34, TSX62, TSX88, TSX55, TSX94, TSX155, TSX188, TSX308, TSX312, TSX447, TSX458, TSX505, TSX506, TSX541, TSX308, TSX361A, TSX447, TSX596, TSX606, TSXU828, TSXU829, TSXU831, TSXU832. Center to center on the 2 mounting studs is 2 5/16 inches. This carburetor comes with studs that attach to carburetor. THIS WILL NOT WORK IN THOSE APPLICATIONS THAT STUDS MUST BE USED IN THE MANIFOLD. 2 5/16 INCHES CENTER TO CENTER ON MOUNTING BOLTS. Made in USA, 1 year warranty. (Part No: 12522) $269.50

Carburetor, New - For TO30, TO35 (Deluxe & Standard), 35, 40, MH50 (Ferguson Industrial), A-145, Z-145, Replaces Marvel-Schebler TSX605, TSX683, TSX882. 2 3-8 inches center to center on mounting bolts. Made in USA.. (Part No: 533969M91) $323.18

Carburetor, New - With Mounting Gasket. Fits TE20, TO20, TO30. New Carburetor has a different polished finish than the original Marvel-Schebler. Parts are interchangeable with original. Replaces Marvel-Schebler carburetor numbers TSX458 and TSX361A. (Part No: 181643M91) $193.50

Carburetor, New - Fits TE20, TO20, TO30. New Carburetor manufactured to duplicate original Marvel-Schebler design. Parts are interchangeable with original. Replaces Marvel-Schebler carburetor numbers TSX458 and TSX361A. (Part No: 181644M91) $199.95

Carburetor, Rebuilt - Fits TO20, TO30 - replacement for OEM TSX458. Add $50.00 core charge to price - this charge is refundable if you send your core to us. (Part No: 1604-CARB) $147.39

Fuel Cap - For models TO20, TE20, TO30, TO35, 1100, 1150, 135, 150, 165, 175, 203, 205. Replaces OEM 520948M91. This is a non-vented cap. (Part No: D5NN9030A) $9.98

Fuel Cap, Vented - CHROME cap for Pony, Pacer, TE20, TO20, TO30, 35, F40, 50, 65, 85, 88, 90, 135, 150, 165, 175, 1080, 1100, 1130, 1150, 1500, 1800, 202, 203, 204, 205, 302, 304, 356, 2135, 3165. Replaces 850493M1. 2 5/8 inch outside diameter (Part No: 520948M91) $9.98

Fuel Tank - Like original, drilled for toolbox. For models TE20, TO20, TO30. Replaces 181637M91. (Part No: S.43668) $197.96

Fuel Tank - Direct replacement for tractors with 80, 87mm standard gas engines. Will work for Continental Z120, Z129 sediment bowl will be 1" forward of original with no holes predrilled for tool box. For Models: TEA20, TE20, TO20, TO30. (Part No: 181637M91) $221.56

Quadrant Stop Kit - For models TE20, TE35, TEA20, TO20, TO30, TO35, 35, 40, 50, 65, Massey Harris 50. Replaces: 825753M1. (Part No: 9N521) $9.99

Sediment Bowl Assembly - For models F40, MH50, TE20, TEA20, TO20, TO30, TO35, 35, 35 Ind, 50, 65, 85, 88, 203 with SN<343891, 356 with SN<670001084. Sediment Bowl Assembly. 2" Bowl. (Part No: 180141M91) $20.50

Sediment Bowl Assembly - For models TE20, TO20, TO30, TO35, all with Continental Z120, Z129, or Z134 Gas engines. Sediment Bowl Assembly. To fuel line is 1/8" pipe connection, 3/8" pipe connection to tank. (Part No: 61782C91) $28.04

Gauges
Ammeter Assembly - Fits all TO & MF models using 30-0-30 amperes. Non-luminous, chrome bezel for 2 inch hole. Replaces 515521M91. (Part No: A0NN10670A) $8.98

Ammeter Black Ring - Fits all TO & MF models using 30-0-30 amperes. Black bezel for 2 inch hole. Replaces 515521M91. (Part No: A0NN10670A-BLAC) $10.38

Oil Pressure Gauge - 80 lb. oil gauge. Fits TE20, TEA20, TO35, MF35, MF50, MF65, Massey Harris 44, 55 Series. For 2 inch hole. Replaces OEM 506902M92. (Part No: FAD9273A) $15.52

Oil Pressure Gauge with Male Fitting - (1/8 inch NPT) For models TE20, TEA20, TO20, TO30. (Part No: S.61466) $15.40

Oil Pressure Gauge, White Face - Chrome bezel. 3/8"-24 UNF female thread. For models TE20, TO20, TO30, TO35, F40. All with Z120, Z129, Z134. (Part No: 180100M92) $17.44

Proofmeter Drive Assembly - For a DELCO Generator. This improved design uses a steel drive gear (originals used a fiber gear). Proofmeter Drive Assembly mounts on original type generator - Fits TO20, TO30, TO35, 35, 50, 65, 85, 88, Super 90, 135, 150, 175, 180, 1080, 1100, Industrials: 30, 31, 35 Turf & Utility, 50, 2135, 2200, 2500, 3165, 202, 204. ALL GAS ENGINES. Includes Housing, 2 drive gears and gaskets. Does NOT include cable. (Part No: 1751295M91) $39.78

Hitch / Drawbar
Clevis - Clevis assembly with pins, for SDA6. For MF50, TO20, TO30, TO35. (Part No: SDA2) $42.80

Drawbar Kit, Swinging - Swinging Drawbar Kit. Painted Red. Contains Drawbar: 29.35" long, 2.00" wide, 1.00" thick, Rear Drawbar Hanger, Drawbar Clevis Assembly and Drawbar Clevis Pin. For models TE20, (TEA20 late only), TEF20, TO20, TO30, TO35, FE35, 50. (Part No: 49A34R) $113.25

Drawbar, Swinging - Drawbar is 29.375 inches in length, 2 inches wide, 1 inch thick, off-set. For models 50, 35, 851, 860, TO20, TO30, TO35. (Part No: 49B70R) $41.69

Hitch Eyelet Bushing - Verify measurements: 7/16 inch x 5/8 inch x 1 1/2 inch. For models TEA20, TE20, TO20, TO30, TO35, 35, 50. (Part No: 180859M1) $1.98

Leveling Box Assembly - Fits: TO20, TO30, FE35, 35, 50 (Up to SN# 518703), MH50. Replaces 182642M91. Center to center OPENS TO MAXIMUM 21.5 inches. (Part No: 8N577A) $68.80

Leveling Box Fork - A=5/8", B= 3/4, C= 11/16", D=14-3/16". For tractors: TE20, TO20, TO30, TO35, FE35, F40 MF35, MF135, MF150, MF65 (used in standard right hand assembly with 10-1/2" shaft), also left hand on MF65. (Part No: 184358M1) $30.96

Leveling Box Fork - A= 5/8", B= 3/4", C=1/2", D=9-3/4". For tractors: TE20, TEA20, TEF20, TO20, TO30, (TO35 when used with 14" shaft). (Part No: 890674M1) $25.68

Leveling Box Shaft - Shaft & pinion, leveling box, 10-1/2 long. For tractors: TE20, TO20, TO30, MF35, MF135 (Used in standard Right Hand assy. with 14-1/2 yoke). For MF165, MF65 (Part No: 185220M1) $25.76

Leveling Rod, LH - Hole-to-hole length is 20" Fits: TE20, TEA20, TEF20, TO20, TO30, FE35, TO35, F40. (Part No: 182544M92) $44.40

Lift Arm, Lower, Right or Left - Lift Arm - Red. Category 1. 32" length to hole centers, 7/8" holes in end sockets (swivel type). Replaces 180846M91 and 30543E91. For tractors: TE20, TO20, TO30 right or left. (Part No: 180846M91) $46.31

Lift Arm, Lower, Right or Left - For models TO20, TO30. This CAT I lift arm has 31 1/2" center to center and is 1/2" Thick. (Part No: 1808467M1) $46.33

Low Link Pivot - Pivot shaft for lower link. Threaded ends 5/8 NF & 5/8 NF, overall length 5-1/4. For tractors: TO20, TO30, TO35, MF35, MF135, MF150 industrials: 2135, 3165, 202, 204. For MF1130 (Part No: 181229M5) $13.54

Lower Lift Arm - RH/LH For models TEA20, TE20, TO20, TO30, TO35. This arm has.875" pin holes, 32" center to center). Also replaces 180846M91 and 1902. (60450S) (Part No: 180847M91) $46.31

Stabilizer Arm Red - Stabilizer arm for =3-point hitch, 31-1/2 hole spacing. For models F40, TO20, TO30, TO35. (Part No: 181778M1) $14.30

Stabilizer Arm, Red, HD - Stabilizer arm for 3-point hitch, high alloy steel, 31-1/2" hole spacing. For models F40, 50, TO20, TO30, TO35. (Part No: 181778M1-XHD) $23.80

Stabilizer Bar, Adjustable - 28-1/2" to 35", 7/8" hole in both ends. For models TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: S.00184) $35.00

Stabilizer Bracket-LH - For models TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: 181776M91) $22.90

Stabilizer Bracket-RH - For models TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: 181775M91) $22.16

Stay Arm Red - Stay arm lower, 1/4 thick steel. For models TE20, TO20, TO30. (Part No: DBSL) $12.34

Stay Arm Red - Stay arm upper, 1/4 thick steel. For models TE20, TO20, TO30. (Part No: DBSU) $12.50

Stay Chain Clevis Kit - Comes with pins. For tractors: TO20, TO30, TO35, MF35, MF50. 11-1/2 long. (Part No: 180861WP) $6.52

Swinging Drawbar Hangar - For models 50, TO20, TO30, TO35. Rear Drawbar Hanger. Used in Drawbar Kit #49A34R. (Part No: 49B71R) $39.60

Swinging Drawbar Hanger - Drawbar hanger for swinging drawbar. For MF50, TO20, TO30, TO35 (Part No: SDA3) $42.51

Hydraulic System
Bushing - Bushing, hydraulic pump base, for PTO shaft. For tractors: TE20, TO20, TO30. Replaces OEM 181095M1. (Part No: 9N649A) $29.94

Chamber Kit - Repair kit for one hydraulic pump chamber. Fits either Left or Right Chanbers. CHAMBER KIT For TE20, TO20, TO30. (Part No: 9N621KIT) $25.80

Dipstick - Hydraulic oil level indicator. For tractors: TO20, TO30, TO35. Replaces 180366M1. (Part No: 193400M1) $9.38

Draft Control Plunger - For TE20, TEA20, TO20, TO30. Replaces OEM 890700M1. (Part No: 8N541B) $34.95

Hydraulic Control Valve - Fits TE20, TEA20. TEF20, TO20, TO30. (Part No: 9N640) $21.49

Hydraulic Control Valve - For models TO30, 50 Massey Harris (Part No: 181163M1) $24.51

Hydraulic Cylinder-2 1/2 Inch - For models TE20, TEA20, TEF20, TO20, TO30. Also replaces OEM #201183. (Part No: 829382M1) $86.40

Hydraulic Lift Cover Gasket Set - For TO20, TO30, TE20. Hydraulic Lift Cover Gasket Set includes 2 Valve chamber gaskets, lift cover gasket, base pump gasket, 2 inspection cover gasket cylinder to center housing cover, 2 hydraulic lift cylinder housing gasket. (Part No: LCRK928) $9.72

Hydraulic Lift Cylinder Piston, 2 1/2 inch - For TO20, TO30, TE20, TEA20, (FE35 above SN# 65684), 50 All with 2-1/2" Diameter Piston), TO35 SN<179303 with 2-1/2" Diameter Piston. Hydraulic Lift Cylinder Piston. DOES NOT come with Rings set (part # 9N675). Rings Set is available for an additional charge. Indicate in comments section of order if needed. (Part No: 181983M1) $38.55

Hydraulic Lift Rod - For models TE20, TEA20, TEF20, TO20, TO30. (Part No: 180903M2) $26.45

Hydraulic Lift Shaft - For models TO20, TO30. Does Not come with 9N531C bushings. 37 Splines On Each End. (Part No: 890722M1) $272.73

Hydraulic Pump Cam Block - Cam block, hydraulic pump. For tractors: TE20, TO20, TO30, TEA20, TEF20. (Part No: 181066M1) $51.81

Hydraulic Pump Overhaul Kit - For TE20, TO20, TO30, TEA20, TEF20. Kit contains cam blocks, pistons, chamber repair kits, PTO shaft bushing, safety valve, and gaskets. (Part No: HPOK1) $199.00

Hydraulic Pump Piston - Piston, hydraulic pump. For tractors: TE20, TEA20, TEF20, TO20, TO30. (Part No: 890675M1) $34.97

Hydraulic Pump Rebuild Kit, Comprehensive - For models TE20, TO20, TO30. Kit contains 2 cam blocks, 2 Pistons, 2 Chamber Repair Kits, PTO Shaft Bushing, Safety Valve, 2 Valve Chambers, 4 copper washers, Base Gasket, Sump Pump Gasket, 2 Side Gaskets, PTO Shaft Gasket, 2 Side Plate Gaskets. (Part No: S.61725) $358.56

Hydraulic Pump Safety Valve - For: TE20, TEA20, (TEF20, before SN# 330043), TO20, TO30. Relief Valve rated to 2000 PSI. **Note: The part you recieve may look different than pictured, but will fit and work the same. (Part No: 181087M1) $30.52

Hydraulic Pump Safety Valve - For (TE20, TEA20, TEF20, before SN# 330043), TO20, TO30. Relief Valve rate to 2000 PSI. (Part No: 181087M91) $30.66

Hydraulic Pump Valve Chamber - Right Hand Valve Chamber, less valves. For tractors: TE20, TO20, TO30. Also replaces 181074M91. Polished Steel Finish. (Part No: 9N621) $131.97

Hydraulic Pump Valve Chamber - Right Hand Valve Chamber, Less Valves. For TE20, TO20, TO30. Cast Iron. (Part No: 9N621-C) $102.36

Hydraulic Pump Valve Chamber - Left Hand Valve Chamber, Less Valves. For TE20, TO20, TO30. Cast Iron. (Part No: 9N622-C) $102.36

Hydraulic Pump Valve Chamber - Left Hand Valve Chamber, less valves. For tractors: TE20, TO20, TO30. Also replaces 181076M91. Polished Steel Finish. (Part No: 9N622) $131.75

Hydraulic Pump Valve Chamber Assembly, LH - Left hand valve chamber with valves. For models TE20, TO20, TO30. Cast Iron. (Part No: 9N622-ASSY) $106.92

Hydraulic Pump Valve Chamber Assembly, RH - Right hand valve Chamber with valves. For models TE20, TO20, TO30. (Part No: 9N621-ASSY) $106.92

Lift Arm - For models TE20, TEA20, TO20, TO30, FE35, F40, TO35, 130, 135, 202, 203, 204, 205, 2135, 25, 302, 304, 35, 65. Lower lift arm for both RH/LH side. Lift arm has a 1.80" I.D. and 37 spline hole. (Part No: 180910M1) $67.86

Lift Cylinder Housing Gasket - For models TE20, TEA20, TO20, TO30. Replaces 181059M1. (Part No: 9N553) $1.02

Lift Shaft Bushing - Bushing is 2.36 O.D., 1.97 I.D., 1.39 long. For tractors: TE20, TEA20, TEF20, TO20, TO30, FE35, F40, TO35, MF35, MF50, MF65, MF135, MF150, MF165. For shaft 184359M2, 4 required. If Shaft 897567M3 is used, it requires bushing 1870934M1 not supplied. (Part No: 181018M1) $8.24

Lift Yoke - With 5/8" x 24 thread. For models TE20, TEA20, TEF20, TO20, TO30. Replaces OEM 181055M1. (Part No: 9N546C) $31.11

Lights
Bracket Set For lights - Fits rounded fenders. For models TE20, TEA20, TO20, TO30, TO35, FE35, F40, MH50, MF50, 65, 85, 90, 135, 150, 165, 175, 230, 235, 240, 245, 250, 255, 265, 270, 275, 282, 290, 298, IND 20, 20C, 20D, 30, 30B, 30D, 40B, 50C. Replaces 1750674M1, 52335M1, 523334M1. (Part No: 1750673M1) $39.98

Clips, Bulb Retaining, (Pack of 4) - Replaces 1750642M1. For models TO30, 50, 65, 85, 88, Super 95. (Part No: S.43070) $10.98

Headlight Bracket, Winged, Left - Left Side. For TO20, TO30, 20, 30, 35, 40, 50, 65, 95. Replaces 510439M1. (Part No: 9N13473) $29.16

Headlight Bracket, Winged, Right - Right Side. For TO20, TO30, 20, 30, 35, 40, 50, 65, 95. (Part No: 9N13472) $29.16

Headlight, 6 Volt, LH - Light is NOT an original replacement. For: TO20, TE20, TO30, TO35. Painted light grey. (Part No: 2N13006C) $46.86

Headlight, 6 Volt, RH - Light is NOT an original replacement. For: TO20, TE20, TO30, TO35. Painted light grey. (Part No: 2N13005C) $46.86

Light Switch, Fused - For models TO20, TEA20, TE20, TO30. Replaces OEM 830517M91. (Part No: 8N11654B) $13.30

Sealed Beam Bulb, 6 Inch - Sealed beam bulb 6-volt using double screw wire connectors. For models TE20, TO20, TO30, TO35 (L4019). (Part No: 1002802M91) $17.94

Side Light Bracket, Bulter - Fits RH or LH side. For Models: TO20, TO30, TE20, TE30. Replaces 54575183. (Part No: 54575182) $16.45

Tail Lite, License Light, Clear Glass Lens - For models TE20, TO20, TO30, TO35, MF35, 40, 50, 65, 85, 90, 135, 202, 204, 205, MH50. (Part No: 1750664M1) $17.00

Tail Lite, License Light, Lens Gasket - For models TE20, TO20, TO30, TO35, MF35, 40, 50, 65, 85, 90, 135, 202, 204, 205, MH50. (Part No: 1750666M1) $7.20

Worklight Switch - For models TO20, TE20, TEA20, TO30, TO35. (Part No: 1750656M1) $15.30

Miscellaneous
Tractor Cover - Grey with red "Ferguson" script. For Models: TE20, TO20, TO30, TO35. (Part No: S.44104) $147.85

Oil System
Engine Oil Dipstick - For models TE20, TO20, TO30, TO35, 35, 50, 135, 150 all with continental gas engine. (Part No: 1750095M1) $22.82

Oil Filler Cap - For models TE20, TEA20, TO20, TO30, TO35, F40 and those using clip type caps. Oil Filler Cap will also replace gas fuel cap (not diesel). Does come with gasket. Gasket not available. (Part No: 760029M91) $14.25

Oil Filter - For Gas: 135, 202, 204, F40, 135, 150, 165, 35, 50, 65, 50, TO30, TO35, 11, Pacer, Mustang, Pacemaker, Pony, Super 90, 20, 202, 203, 204, 205, 2135, 2155, 2200, 23, 2500, 40, 72SP, 82SP, 88, 85, 90SP, 92SP, Colt, F40. Replaces 835817M91, 1003879M11, 1014219, 1754468M91, 185551M92. (Part No: APN6731B) $11.54

Oil Filter Adapter Kit, Spin On - For models T030, TO35, 35, 50, 135, 135 Deluxe, 150, F40, all with Z129, Z134 or Z145 Continental Engines. Engine Oil Filter Adapter Plate for spin on oil filter(Includes Filter). For ordering extra filters, use part S.66491 in comments section of order form. (Part No: S.42809) $29.93

Oil Filter-Tripac - Tri-pac of oil filter elements. Kit of three APN6731B. For early GAS tractors: 11 Pony, 16 Pacer, 20, 22, 23, 30, 33, 333 TO30, TO35, MF35, F40, MF50, MF65 (replace. orig. Fram C3 element), MF85, MF88, Super 90, MF135, MF150, MF165 35, 65 turf & utility ind For 203, 205, 20, 2135, 302, 304, 30, 3165, 356, 35, 65, F40, MF135, MF150, MF165, MF35, MF50, MF65, MF85, MF88, Super 90, TO30, TO35. Replaces 835817M91. (Part No: APN18649B) $25.85

Oil Pump Kit - Complete repair kit. For models TE20, TO20, TO30, TO35, 35, 135, 50, AND 150 with Continental 2 15/16" O.D. drive gear. Replaces 835643M1. (Part No: OPK60A) $71.27

PTO / Driveline
Bearing - Bearing, outer, for PTO output shaft (I.D. 1.771" X O.D. 2.952" x .629" thick) For tractors: TO30, TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175 late production, MF235 For tractors with dry brakes: MF255, MF265 to SN# 9A349239, MF275 to SN# 9A349239. For tractors using snap rings on bearing. (Part No: 195498M1) $24.26

Bearing - PTO shaft ball bearing. For tractors: TE20, TEA20, TO20, TO30. (Part No: GA1773) $4.18

PTO Cover - PTO cap, aluminum alloy replacement. For tractors: TE20, TO20, TO30 all with 1-1/8 or 1-3/8 shafts. For MH44. Replaces 825787M1. (Part No: 310088) $7.56

PTO Housing Gasket - For TE20, TO20, TEA20, TO30. PTO Housing gasket. (Part No: C5NN747A) $.99

PTO Shaft - PTO shaft only, 1-3/8" 6-spline, converts original 181173M1 from 1-1/8" 6-spline, to 1-3/8" 6-spline. For tractors: TE20, TO20, TO30 (includes 181183-38 retainer sleeve). (Part No: 181173-38) $56.39

PTO Shaft Conversion Assembly - Shaft assembly with cap converts 1-1/8 inch PTO system to 1-3/8 inch. This is a complete Assembled shaft with bearing & housing assembly that is ready to install by removing 4 bolts from cover. Length 30-7/8 inches. Fits: TO20, TE20, TEA20, TED20, TEF20, TO30. (Part No: 9N700-38) $92.90

PTO Shaft Seal, Double Lip - PTO oil seal fits 1-1/8 or 1-3/8 PTO shaft. 2.45 O.D., 1 5/8 I.D., 5/8 wide. For models TE20, TO20, TO30. Replaces 195763M1. (Part No: D9NN703BB) $7.06

PTO Shaft Sleeve - For original PTO Shafts for models TEA20, TED20, TEF20, TE20, TO20, TO30. Will not fit replacement shafts. (Part No: 181183M1) $5.74

Sleeve Bushing - Retainer sleeve for Tisco 181173-38, 1-3/8 6-spline PTO shaft. For TE20, TO20, TO30 (Part No: 181183-38) $4.80

Paint
Paint, Dark Gray, 1 Gallon - From TISCO, providing OEM quality. For TO20, TO30 1946-54 and implements before 1955. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP230GAL) $42.53

Paint, Dark Gray, 1 Quart - From TISCO, providing OEM quality. For TO20, TO30 1946-54 and implements before 1955. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP230QT) $24.74

Seats
Bucket Style Base Cushion - Approx 19" wide x 15" deep x 5" thick. Has strap to secure bottom. For model s:MH50, TE20, TO20, TO30, TO35, F40, 30, 35, 50, 65, 85, 88, 95, 130, 135, 165, 185, 230, 235. This seat cushion is GREY grained vinyl. (Part No: R1000) $54.00

Bucket Style Metal Pan Seat - Color may vary. Size is approx 19" wide x 13" deep x 9-1/2" high. Fits Models: TE20, TEA20, TO20, TO30, TO35, MF50, MH50, MF35, 50, 65, 85, 88, 98, 135, 150, 165, 230, 235, 240, 245, 250, 265, 283, 333, 444, 555, 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 50, 50A, 50C, 200, 2135, 2200, 3165. Uses Cushions NO. R1001 and NO. R1000. Purchase complete assembly as PART NO. MFSEAT (Part No: 181313M93) $64.13

Bucket Style Seat & Backrest - Grey Seat cushion and backrest cover and inlay assembly. For models MH50, TE20, TO20, TO30, TO35, F40, 30, 35, 50, 65, 85, 88, 95, 130, 135, 165, 185, 230, 235. This kit contains: Backrest Assembly (181324M1 inlay & 513353M91 cover), Seat Cushion Assembly (181326M1 inlay & 513351M91 cover). (Part No: FCX810) $82.12

Bucket Style Seat Assembly - Includes Black Primer Metal Seat Pan)and Grey Cushion Assembly with backrest and cushion, Fits Models: TE20, TEA20, TO20, TO30, TO35, MF50, MH50, MF35, 50, 65, 85, 88, 98, 135, 150, 165, 230, 235, 240, 245, 250, 265, 283, 333, 444, 555, 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 50, 50A, 50C, 200, 2135, 2200, 3165. (Part No: MFSEAT) $142.47

Bucket Style Seat Back - Curved seat back measures approx 16" wide x 4-1/2" tall x 2" deep. Has 2 mounting studs (on back) spaced approx 9-1/4" apart. For models MH50, TE20, TO20, TO30, TO35, F40, 30, 35, 50, 65, 85, 88, 95, 130, 135, 165, 185, 230, 235. This seat back is GREY grained vinyl. (Part No: R1001) $30.00

Pan Seat - 19 inch wide with Nine Holes For TE20, TO20, TO30, MF35, MF40, MF50 (Part No: 8N400) $43.04

Pan and Seat Cushion Set - Comes with black metal pan, black bottom cushion and black backrest cushion with metal plate and hardware. For Models: 135, 150, 165, 20, 20C, 20D, 2135, 2200, 235, 245, 265, 282, 283, 30, 30B, 30D, 30E, 3165, 35, 40, 40B, 50 LOADER, 50A, 50C, 555, 65, 85, 88, 98, TE20, TEA20, TO20, TO30, TO35. Replaces 181313M93, 181324M1. (Part No: 1210-1604) $106.50

SEAT SPRING - Seat spring. Tractors: TE20, TEA20, TO20, TO30, FE35, F40, MF35, F40, F50. (Part No: 825608M1) $47.29

Seat Bumper, Rubber - For use in a flip top pan seat (NOT a bucket seat), .957" head dia., .302" stem length, 1.283" overall length. For models TO20, TO30, 35, 40, (50 up to SN# 514381), 65 diesel special, 135, 202, 204, 2135. Replaces TO434A. (Part No: 180289M1) $7.00

Seat Pan, Flip-over - For models TE20, TEA20, TO35, FE35, F40, TO20, TO30, MH50. (Part No: 181330M91) $46.68

Sheet Metal / Body Parts
Bolt, Hood Pivot - For models TO20, TO30, TO35, TE20, TEA20, 35. One used on each side panel. (Part No: 180718M1) $4.66

Bumper - For TE20, TO20, TO30, 35 - has 3 front vertical bars to protect tractor grill plus heavy duty horizontal bumper. Painted red, axle mount with mounting brackets. This is an aftermarket item. Add an additional $20.00 for shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: BU1021) $267.76

Fender With Bracket - With NON-ORIGINAL TYPE BRACKET. Rear fender, dished type with mounting bracket, mounting bracket spot welded on. For tractors without roll-over protection structure. No tool box hole. For tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 exc. orchard, MF150, MF165, MF175, MF230, MF235 exc. vine & orchard, MF245, MF255 with 16 rims, MF265 std., MF275 std., MF285 std. industrials: 20 except turf, 20C except turf, 30 except turf, 30B, 35 utility, 40, 50, 50A, 202, 203, 204, 205, 2135 utility, 3165 utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. For MF1100, MF1105, MF1130. Additional Shipping of $20.00 per fender due to the weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 526905M91LR) $116.78

Fender, Clamshell with Bracket - For models FE35, TE20, TO20, TO30, 135, 35, 230, 235, 245, 2135, 20 'Clamshell, large lip' style Fender with Bracket. Additional shipping charge of $20 will be added to your order due to size and weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 180707M92) $120.15

Fender, Clamshell with O Bracket - Fender panel, dished type, less mounting brackets, made exactly like the original. For tractors without roll-over protection structure. For tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 exc. orchard, MF85 std., MF135 exc. vine & orchard, MF150, MF165, MF175, MF230, MF235. Add additional $10 shipping per fender due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 526904M1) $89.53

Grill - For models TO20, TO30. (Part No: 181627M91) $188.00

Hood - For models TO20, TO30. (Part No: 181709M91) $441.42

Hood, Dash & Grill Rubber Bumper - 1/2" O.D. X 7/16" tall. For models 20C, 20D, 20F, 30B, 30E, 30H, 40B, 40E, 50A, 50C, 50D, 50E, Super 90, TE20, TO20, TO30, 30, 31, 60, 65, 85, 88, 135, 150, 165, 175, 180, 202, 203, 204, 205, 230, 231, 235, 240, 245, 250, 255, 265, 302, 303, 404, 1080, 1100, 1130, 1150, 2135, 2200, 2640, 2675, 2705, 2745, 2775, 2805, 3165, 3505, 3525, 3545, 4500, 6500, MF 20, MF 25, MF 35, F40, MF (Ag & Ind): 40, 50, TO35. Replaces: 194768M1. (Part No: 180673M1) $1.00

ROP Frame Assemply - Roll Over Protections - Cross Bar Type. Fits TO20, TO30, TO35, F40, TE20, MF30, 35, 50, 130, 135, 148, 150, 240. Due to truck freight of this 100 lb item, additional shipping above the regular shipping cost has already been added to the price. (Part No: MF1) $833.00

Rubber Hood Pads - **ENTER 10 in QTY. Rubber Hood Supports. These rubber pads fit onto cowling under hood. For TE20, TEA20, TO20, TO30, TO35, f40. Replaces OEM 180673M1. **Must be ordered in quantities of 10.** Priced each. (Part No: C5NN16N655B) $0.90

Side Panel, LH - For models TO20, TO30. (Part No: 181704M91) $134.95

Side Panel, RH - For models TO20, TO30. (Part No: 181705M91) $134.95

Step Plate - Left - For TE20, TEA20, TEF20, TO20, TO30, TO35. Left Hand Step Plate. Includes rear bracket. 24 inches in length. (Part No: 180717M91) $49.48

Step Plate - Right - For TE20, TEA20, TEF20, TO20, TO30, TO35. Step Plate - Right. Includes rear bracket. 24 inches in length. (Part No: 191929M92) $49.98

Step Plate Bracket, Rear - For use with 61127S and 61128S Step Plate Assembly. Fits: TE20, TEA20, TEF20, TO20, TO30, TO35. Replaces 180590M1. (Part No: S.42997) $20.80

Toolbox - Metal comes primered, COLOR MAY VARY. Restoration Quality. 11" X 4 1/2" X 4". Fits TRACTORS: TE20, TO20, TO30, TO35, 135, 165UK, 240, 250, 550, 560, 565, 575, 670, 690, 698, 699. Fits INDUSTRIALS: 20E, 20F, 30E, 40E, 50E. Replaces 1662749M91 AND 909616M94. (Part No: 825633M91) $31.59

Steering
Axle Bushing - Front pivot support bushing. For tractors: TE20, TO20, TO30, TO35. 1-15/16" O.D., 1-25/32" I.D., 1-1/2" long. (Part No: 180344M1) $7.50

Axle Bushing, Flanged - Front pivot support bushing with swept back axle. 2.075" O.D., 1.750", .820" long. For models TE20, TO20, TO30, TO35, MF35, MF135, MF235, 20, 2135. Length of bearing may vary but will fit application if over .790 inch. (Part No: 182850M1) $10.78

Bearing and Seal Kit, Front Hub - Kit includes (1) Inner Bearing 1850224M91, (1- Outer Bearing 150662M11, and 1- Seal 897363M1. Fits on models TE20, TEA20, TEF20, TO20, TO30, TO35, FE35> SN# 368185. Note: The Hub (shown in picture) is NOT included. (Part No: S.02970) $28.82

Front Axle Pin - For TO20, TE20, TEA20, TO30. Front Axle Pin. 1 3/4" Diameter 4 1/4" Length. (Part No: 825002M1) $32.09

Pivot Pin - Pivot pin for swept back axles. VERIFY OVERALL LENGTH. 1-3/4" O.D., 5 1/2" long, 7/8" bolt hole and 1" dia. crank hole. LENGTHS also available 4.75 or 5.25 inches (call for pricing). Fits TO20, TO30, TO35, 35, 135 prior to SN# 9A86902; industrials: 20 prior to SN# 9A86902; 2135 turf & narrow. Replaces 193746M1. (Part No: 183221M1) $36.08

Power Steering Pump Filter - Measures 1.02 inches I.D., 2.99 inches O.D., 1.61 inches height. For models 11, Pony, 16, Pacer, 175, 180, 20, 202, 204, 2135, 2155, 2200, 230, 235, 245, 30, 302, 303, 304, 30B, 30D, 3165, 333, 35, 4500, 50, 50D, 555, 555D, 55D, 55G, 55K, 55LP, 65, 85, 88, Colt, FE35, FE35X, 50, Mustand, Pacemaker, TO30. VERIFY MEASUREMENTS of old filter. Replaces 1008553M1, 1052262M91, EP3. (Part No: P183) $7.85

Seal, Power Steering Pump Driveshaft - For models 135, 20, 200, 20C, 20D, 20E, 2135, 2200, 230, 235, 240, 245, 250, 2500, 30B, 30D, 30E, 35, 40, 4500, 50, MH50, 65, TO30. (Part No: 1751651M1) $9.99

Spindle Bushing - For models 135, 148, 20, 20C, 2135, 230, 235, 240, 250, 35, FE135, FE35, TE20, TO20, TO30, TO35. Bushing Measures 1.395 inches O.D. X 1.265 inches I.D. X 1.5 inches Long. Note: Must be ordered in qty of 4, Priced each. (Part No: 180345M1) $5.36

Spindle Nut - Replaces 353928X1, Castle nut is 3/4" x 16UNF. Fits Massey : TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, F40. (Part No: 387930S36) $1.60

Spindle Repair Kit - (4) 180345M1 bushings, (2) 18560X thrust bearings, (2) 180355M1 spindle dust seals. For models FE35, TEA20, TED20, TEF20, TE20, TO20, TO30, TO35, 135, 20, 2135, 230, 235, 240, 240S, 35. (Part No: SBBSKIT01) $32.64

Spindle, LH - A=11", B=1 1/4", C=3/4" UNF. For models TE20 SN# 49999>, 35, FE35, TEA20, TED20, TEF20, FE35> SN# 368615, TO20, TO30, TO35. Also replaces OEM #897415M91. (Part No: 180349M92) $75.48

Spindle, RH - A=11", B=1 1/4", C=3/4" UNF. Fits models TE20 SN49999>, 35, FE35, TEA20, TED20, TEF20, TO20, TO30, TO35, MF35. Also replaces OEM #897414M91. (15985S) (Part No: 180346M92) $75.48

Steering Arm - For models TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, 135 UK. (Part No: 180350M1) $47.50

Steering Column Cover - Chrome cover includes spring & felt seal. Fits TE20, TEA20, TEF20, TO20, TO30. (Part No: 890576M1) $19.76

Steering Gear Inner Bushing - For models TEA20, TE20, TO20, TO30. Verify measurements of 1 1/8 x 1 7/16 x 1 1/8 inches. (Part No: 195783M1) $22.68

Steering Gear Outer Bushing - For models TEA20, TE20, TO20, TO30. Verify measurements of 1 5/16 x 1 7/16 x 1 13/64 inches. (Part No: 180363M1) $27.90

Steering Shaft Bearing - Replaces 760906M1. Price is for 1. Two are used on the steering shaft, one at the top and one at the bottom. For models TE20, TO20, TO30. (Part No: 5BC-TIM) $15.68

Steering Shaft Bearing Cone - Steering Shaft Bearing Cone. Fits TE20, TO20, TO30. (Part No: 4CB-TIM) $29.18

Steering Shaft Bearing Cup - Price is for 1. Two are used on the steering shaft, one at the top and one at the bottom. For TE20, TO20, TO30. Replaces 760907M1. (Part No: 6-TIM) $12.70

Steering Shaft Bearing Kit - Kit consist of 6-TIM quantity 2, 5BC-TIM quantity 2, and 4CB-TIM quantity 2. Steering Shaft Bearing Cone. Fits TE20, TO20, TO30. (Part No: STEERING_KIT) $105.12

Steering Shaft and Gear - Shaft, steering gear: TE20, TO20, TO30. 13 1/2 inches long. NOTE: If the bearings for this shaft are needed please order P/N's: 5BC-TIM (Bearing), 6-TIM (Outer Race), 4CB-TIM (Inner Race). Order times two (X2) for a complete bearing set (Upper and Lower) for one tractor. (Part No: 181365M1) $87.30

Steering Wheel - For TO20, TO30, TO35, 35, 135, 50, & 65. 17-3/4" dia, 3/4" hub with 3/16"keyway. Covered Metal Spokes. (41486S) (Part No: 180576M1) $25.98

Steering Wheel - Original Type - For models TE20, TEA20, TO20, TO30, TO35, 20, 35, 135, 50, 65, 2135. 17-3/4" dia, 3/4" hub with 3/16" keyway. Metal Spokes. (Part No: 180576M1-OE) $39.05

Steering Wheel Nut, Chrome - Chrome, Domed. For models TE20, TEA20, TEF20, TO20, TO30, TO35, FE35, F40, 20, 202, 203, 204, 205, 50E, Pony, Super 90, 135, 135 UK, 270, 283, 290, 298, 35. Repalces OEM 195592M1. (Part No: 351103CC) $14.63

Thrust Bearing - Spindle thrust bearing, 1.250" I.D.. Replaces 195175M1. For models 20, 2135, F40, FE35, MF135, MF150, MF165, MF230, MF235, MF245, MF35, MF50, MF65, TE20, TO20, TO30, TO35. (Part No: 18560X) $17.68

Tie Rod End - 3.594" long, .687" dia., 18 LH thread. For models 135 early, 30, 350, TEA20, TED20, TEF20, TO20, TO30. (Part No: 180391M91) $13.98

Tie Rod End - Replaces OEM #194606M91. 3.250" long, .687" dia., 18 RH thread. For models 135 early, 30, 35, TEA20, TEF20, TED20, TO20, TO30. (Part No: 180381M91) $13.09

Wheels
Bolt & Nut Kit - Rear Rim to Wheel Center - Kit contains (1) 2.88"x5/8" UNF bolt (bolts have a small key at end) with (1) nut. Replaces 828217M1 & 353427X1. For rear wheel on: TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35. (Part No: S.04352) $3.18

Disc-Wheel Center (28 inch) - Fits on models, TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35. 6 Loops - 24 3/8 inch Diameter 8 Lugs - 6" Diameter 4 5/16 Center Hole. Also replaces OEM #1882977M1, 963613M1, 1678566M1. (Part No: S.61133) $222.28

Front Rim, 3.00 x 19 - As OE orignal Front rim 3.00" x 19", uses 4.00" x 19" tire. For models TE20, TEA20, TEF20, TO20, TO30. Additional $10 will be added for shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Uses tire p/n S.78899 and tube S.00207 specify in comments section if needed. Replaces 180367M91. (Part No: C5NN1015S) $93.15

Front Rim, 4.50 x 16 - Front wheel, with weight holes. 4:50 x 16, 6-bolt, 6" bolt circle with 4.62 pilot for 5:50 or 6:00 x 16 tires. 2500 lb. capacity. For models 135, 150, 165, 165 UK, 175, 180, 202, 203, 204, 205, 20C, 2135, 230, 231, 235, 240, 240P, 240S, 245, 250, 253, 263, 265, 270, 275, 290, 35, 360, 375, 390, 390T, 4225, 4235, 4240, 4243, 4245, 4253, 4255, 4265, 4325, 4335, 4345, 4355, 50, 65, 85, 88, Super 90, TE20, TEA20, TO20, TO30, TO35. Replaces 885741M3, 1077283M91, 506020M91, 195638M91. Additional $15 shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 535448M91) $62.91

Front Wheel Stud & Nut Kit - Price shown is package of 6 (6 stud & 6 nut). Verify sizes in picture before ordering (You will have to click on Enlarge Picture under price). Fits: TE20, TEA20, TO20, TO30, TO35, FE35, F40, 1100, 1130, 130, 135, 150, 165, 175, 180, 202, 203, 204, 2135, 250, 253, 255, 263, 270, 275, 281, 283, 290, 30, 3165, 340, 35, 350, 355, 360, 365, 375, 390, 4225, 4255, 4265, 50, 575, 590, 65, 675, 690, 85.Consist of p/n 181328M1 QTY of 6, and 195490M1 QTY of 6. (Part No: MFSTUD&NUTKIT) $28.32

Hub Cap WITH Zerk Fitting - Threaded. For models 135, 150, 202, 203, 204, 205, 2135, 35, 40, 65, FE35, TE20, TO20, TO30, TO35. Has Zerk fitting center of cap. (Part No: 1884289M1WZ) $13.00

Hub Cap Without Zerk Fitting - Threaded. For models 135, 150, 202, 203, 204, 205, 2135, 35, 40, 65, FE35, TE20, TO20, TO30, TO35. (Part No: 1884289M1) $8.12

Rear Rim & Center Assembly - For TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35. Size is 10x28. Replaces OEM part# 897137M92, 1678566M1. Add $80.00 extra shipping due to weight. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: S.61968) $296.80

Rim, 9X28 - For models TE20, TEA20, TED20, TEF20, TO20, TO30, TO35, FE35. 6 Loop 28" dia. Also replaces OEM #897137M92, 1882978M92.Add additional $25.00 per rim to shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 897137M92) $131.36

Wheel Bearing Kit - For models 35, 40, 50, 65, FE35, TE20, TO20, TO30, TO35. Kit contains 1 each:15123(Cone), 15245B(Cup), 09067(Cone), 09195(Cup), 180008M1(Seal).``Replaces 1810391M91, 835964M91 (Part No: WBKMF1) $24.54

Wheel Stud - Studs are 9/16 x 2 inch. For 130 French, 135, 135UK, 150, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 240S Turkey, 245, 30, 3165, 35, 35X, 50, TE20, TEA20, TO20, TO30, TO35. Wheel studs (Min Qty Package of 10, price individually. Must order in multiples of 10) also replaces 185400M1 and 185400M2. (Part No: 825507M1) $2.08

Wheel Stud Nut - Nut fits rear wheel stud. 9/16" NF. Used with 185400M1 & 185400M2 stud. For 130 French, 135, 135UK, 150, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 240S Turkey, 245, 30, 3165, 35, 35X, 50, TE20, TEA20, TO20, TO30, TO35. Wheel nuts (Minimum Qty Package of 10, price individually. Must order in multiples of 10) (Part No: 180004M1) $1.62



Brakes
Brake Rivet Tool - Used to rivet brake lining to existing shoe or band. Includes a tool to drive out the old rivets and a tool to peen the new rivet, mounts into a vice, 1-1/4" throat, 1/8" dia. rivet punch. (Part No: RIVET_TOOL) $35.25

Brake Rivet Tool, Large - Larger version of our Brake rivet tool. 3-3/8" deep throat x 2-1/8" high throat. Includes 1 punch for brake shoe rivets and 1 punch for clutch pulley brake. (Part No: LGRIVET) $89.00

Brake Rivet Tool, Large - Larger version of our Brake rivet tool. 3-3/8" deep throat x 2-1/8" high throat. Includes 1 punch for brake shoe rivets and 1 punch for clutch pulley brake. (Part No: LGRIVET) $89.00

Cooling System
Magnetic Block Heater - Universal. 115-120 AC, 180 watts, draws 2 amp maximum. Surface area 2-3/4 inches x 3-3/4 inches, delivers 300-400 degrees surface temperature. (Part No: MBH1153) $56.70

Water Pump Kit - Repair kit, services pumps 739527M91 & 742558M91. (Part No: 731774M91) $55.54

Decals and Emblems
Ferguson Script Decal - 12" long, vinyl, blue and white. (Part No: R0735) $15.50

Ferguson Script Decal - 19" long, vinyl, green and chrome. (Part No: R0736) $29.46

Ferguson Script Decal - 26" long, vinyl, blue white. (Part No: R0737) $27.93

Massey Harris Trademark Decal - Red with yellow letters, 1-1/2" on vinyl. (Part No: R5190) $4.66

Massey Harris Trademark Decal - Yellow with red letters, 1-1/2" on vinyl. (Part No: R5191) $4.66

Massey Harris Trademark Decal - Red with yellow letters, 6" on vinyl. (Part No: R5192) $15.50

Massey Harris Trademark Decal - Yellow with red letters, 3/4" on vinyl. (Part No: R5236) $3.10

Massey Harris Trademark Decal - Red with yellow letters, 3/4" on vinyl. (Part No: R5237) $3.10

Drive Train
Gear Shift Boot - Fits many Massey Harris Models. May not fit your tractor verify size before ordering. 1-3/4" bottom I.D., 5/8" hole dia. (Part No: VT2017) $13.90

Lucas Hub Oil (quart) - Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks. It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance. It is an excellent gear lube for racing or heavy duty applications. Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088) $9.06

Electrical System
Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. NOTE

Alternator Base Bracket Kit - Universal - Universal base bracket mounting kit. For converting from a generator to an alternator . Contains: brackets, bolts, washers, nuts & Basic Instructions. (Part No: 2348258) $39.25

Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Part No: 8NE10305SE) $106.29

Coil Bracket - Universal Coil Bracket (Part No: R1940) $6.61

Coil, High Performance (Black), 12 Volt, Oil Filled - Pertronix Flame Thrower heavy duty, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40511) $35.99

Coil, High Performance (Black), 6 Volt, Oil Filled - Pertronix 'Flame Thrower' high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. (Part No: 40011) $32.82

Coil, High Performance (Chrome), 12 Volt, Oil Filled - 12-VOLT, Pertronix 'Flame Thrower' Chrome, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40501) $35.99

Coil, High Performance (Chrome), 6 Volt, Oil Filled - 6-VOLT, Pertronix 'Flame Thrower' Chrome, high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40001) $36.89

Coil, Ultra High Performance (Black), Oil Filled - Pertronix 'Flame Thrower II' Black, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kits or any 6 volt system. Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45011) $35.25

Coil, Ultra High Performance (Chrome), Oil Filled - Pertronix 'Flame Thrower II' Chrome, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kits or any 6 volt system using "Ignitor II". Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45001) $39.68

Generator Cutout - Generator cutout for Autolite, 6-volt. For most MH models to 1951. (Part No: CB4014) $27.21

Spark Plug - Extended tip, 14mm thread, 3/4" reach. Replaces Champion N12YC. NOTE: Verify spark plug type before ordering. (Part No: AL65) $3.64

Spark Plug - Extended tip, 14mm thread, 3/8" reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Part No: AL85) $3.64

Spark Plug Wire Set, 4 Cylinder, Universal - For use with Ignitor II high performance electronic ignition conversion kits. (Part No: S.66442) $14.48

Spark Plug Wire Set, Universal, 4 Cyl. - Universal Spark Plug Wire Set, 4 Cylinder, 90 degree boot, cut to length. Longest Reach is 33 inches. Solid brass distributor coils, Zinc-coated plug terminals, tin-coated copper core, boots constructed from EPDM rubber and dual-jacket insulation. Meets SAE J2031 Specifications. Made in the USA. (Part No: CPN12259) $17.22

Spark Plug Wire Set, Universal, 6 Cyl. - Universal Spark Plug Wire Set, 6 Cylinder, 90 degree boot, cut to length, brass terminals, copper strand core. Longest Reach is 33 inches. (Part No: SWS260) $20.02

Starter - Don't see the starter you need for your tractor? We probably have it! (excluding Massey Harris). Just call us at 800-853-2651. NOTE

Starter Drive - Drive assembly for Delco starters. Fits all MF diesel models Perkins gas models. (Part No: 1036519M91) $15.98

Starter Solenoid - Solenoid assembly, saddle mounting to starter. Services most late models, replaces Delco 1115510, on starters 1113139, 1113683, 1113676, others. 12-volt. (Part No: 1028587M91) $19.90

Starter Solenoid - Solenoid assembly, flange mounting to starter. Replaces Delco 1114356 on starters 1108649, 1107503, 1107512, 1108649. Gas & diesel applications. 12-volt. (Part No: 1047083M91) $17.02

Starter, Generator Tag, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO12) $14.40

Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO6) $14.40

Voltage Reducer with Bracket - 12 volt to 6 volt. (Part No: S.52671) $11.82

Voltage Regulator - Voltage regulator, 12-volt. For MF tractors using Delco alternators, replaces 1119507. (Part No: 1031060M91) $26.62

Engine Gaskets
Silicone Black RTV - Permatex black RTV silicone adhesive sealant. Provides a waterproof seal around metal, glass, rubber. Designed for indoor or outdoor use, 3 oz. tube. (Part No: PRM16BR) $7.14

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, Oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 F to +500 F, 3.35 oz. tube. (Part No: PRM77BR) $7.86

Silicone Copper RTV - Permatex ultra copper, hi-temp RTV silicone gasket. Three times more oil resistant than conventional silicones. Use on exhaust manifolds, valve covers, oil pans, water pumps. Temperature range -75 F to +700 F, 3 oz. tube. (Part No: PRM101BR) $11.78

Engine Rebuild Kits
Lucas Assembly Lube - Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces. It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts. Its useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $6.71

Engine Parts
Push Rod - For Diesel Engines AT6.354.4, A6.354.4, C4.236, T6.354, 6.354 Perkins, (AD3.152 with engine SN# less than 2820092). (Part No: 31434307) $5.16

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE

Engine Pistons and Sleeves
Piston Groove Cleaner - For pistons up to 5 1/2 inches. Cleans grooves of 5/64, 3/32, 1/8, 5/32 and 3/16. (Part No: B1SB9055) $24.95

Piston Ring Compressor - Ratchet mechanism with square drive tool to adjust diameter and enlarged crimped edge to prevent compressor from entering cylinder. Depth 6 1/2 inches. Range 3 1/2 to 7 inches. (Part No: 900521) $35.67

Ridge Reamer - Heavy Duty Ridge Reamer. Removes ridges from the top of the cylinder to achieve smooth wall surface on engine bores from 3 to 5 inches. Tungsten carbide blade is reversible for long life. (Part No: 500560) $63.87

Engine Rings
Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32"). NOTE

Exhaust System
Chrome Exhaust Stacks - Universal. Available from 2 to 5 inch inside Diameter. 48 to 53 inch length. Curved top on all sizes. Extended curver available on some sizes. Priced from $69.95. Single wall construction. Chrome Exhaust Clamps are $5.00 each when ordered with a pipe. Call for pricing for the size you need 800-853-2651 NOTE

Rain Cap - This rain cap is for a 2.50 inch pipe. (Part No: R1802) $9.80

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2" x 3-1/4". (Part No: S.43231) $9.90

Choke Cable - Universal choke cable 72 inches long, 7/16 inch thread dia. Being a universal may or may not look like the picture. May say "Choke" or "C" or nothing. (Part No: CC72) $15.22

Fuel Filter, In-Line, 1/4 inch - Inlet 1/4, outlet 1/4, O.D. 1-29/32, length 4-1/16. (Part No: 6511393) $6.92

Fuel Filter, In-Line, 3/8 inch - Inlet 3/8, outlet 3/8, O.D. 1-29/32, length 3-7/8. (Part No: BF836) $6.28

Fuel Filter, In-Line, 5/16 inch - Inlet 5/16, outlet 5/16, O.D. 1-29/32, length 4-5/32. (Part No: BF840) $6.22

Fuel Line Sleeve - 7/16"OD x 1/4"ID x 1/4" wide. Package of ten. (Part No: 376525X1) $5.00

Fuel Tank Liner - For all fuel tanks. One quart Fuel Tank Liner covers tanks up to 12 gallons. Once cleaned, this tank liner will prevent further corrosion inside your tank. (Part No: R2043) $29.99

Fuel Tank Liner Kit - Works on all metal gas tanks, use with gas or diesel fuels. Kit includes 1 qt cleaner, 1 qt prep solvent, and 1 qt tank liner which covers tanks up tp 12 gallons. Includes application instructions. (Part No: NR1259) $65.00

Fuel Tank Repair Kit - Permanent hole and crack repair for metal fuel tanks in 30 minutes. Kit includes instructions and materials needed to fix cracks up to 4" long and holes up to 3/8" in diameter. NOT for plastic fuel tanks. (Part No: FTR180) $27.62

Fuel Tank Webbing, 3 Ft - Black woven nylon type material, .042" thick, 3 foot section. (Part No: FTW494) $8.38

Lucas Fuel Treatment (quart) - Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion. (Part No: LU10003) $9.97

Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8" diameter, 2.150" O.D., Made in the USA (Part No: C1778R) $1.50

Gaskets
Gasket Material, Cork Rubber - 3/32" thick x 12" wide x 24" long. For making general purpose gaskets. (Part No: GSKCR332) $10.95

Gasket Material, Cork Rubber - 1/16" thick x 12" wide x 24" long. For making general purpose gaskets. (Part No: GSKCR116) $13.75

Gasket Material, Exhaust Manifold - 1/16" thick x 12" wide x 28-1/2" long. Perforated steel core to make manifold gaskets. (Part No: GSKEM1228) $19.95

Gasket Paper, .0160 - .0160" x 18" x 98" long. This gasket paper is for general purpose gasket making and NOT for high temperature applications. (Part No: GSKP1844) $14.90

Gasket Paper, .0275 - .0275" thick x 18" wide x 98" long. This gasket paper is for general purpose gasket making and NOT for high temperature applications. (Part No: GSKP1898) $22.90

Gauges
Hour Meter - DC voltages from 12V thru 36V nominal. Heavy duty glass-reinforced polyester body. Internal shock shields & grommets protect movement from shock & vibration damage. Fits 2-1/4" opening, three(3) mounting screws with nuts and two(2) blade terminals included. (Part No: HM771) $43.69

Hourmeter, Analog - 2", black. Can be used on any tractor with a 12 to 24 volt electrical system. (Part No: S.52672) $38.40

Oil Gauge Copper Line Kit - Universal, for tractors using 1/8 x 6 ft. copper oil line. Includes 6 Ft 1/8 Line, 2 x 5/16 -24 UNF Nuts, 2x Compression sleeves, and a 1/8-27 NPTF Female to 5/16-24 UNF male adapter. (Part No: UNI523) $22.75

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8" pipe thread to 1/8" tube. Brass. (Part No: 919095) $14.35

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8" pipe thread to 1/4" tube. Brass. (Part No: IHS626) $14.35

Oil Pressure Gauge - Universal Complete assembly with oil tube and mounting hardware, Lighted. 80 psi. Line uses 1/4 inch connection with adapters for 3/8 and 1/2 inch. (Part No: SSW0002) $15.95

Temperature Gauge - Universal water Temperature gauge(0-280 degree scale). Fits model using 2 inch gauge. Comes with 70 inch capillary tube and will fit a 1/2 inch or 3/4 male adapter, engine block or radiator threaded hole. (Part No: 1042944) $23.85

Temperature Gauge, Universal - For 2" mounting hole. Complete assembly with bracket and adapters for block. Install in block, head or hose. Temperature is measured in 3 zones (COLD, NORMAL, HOT). Black face with white needle. Extra-long 77" capillary line. Fits all liquid cooled engines. (Part No: UTG50) $25.30

Hitch / Drawbar
Bracket Stabilizer - Bracket, used with telescoping stabilizer 539881M2TSK. (Part No: 514992M2) $40.93

Center tube, Stablizer - Center tube for SK102CH stabilizer kit. (Part No: SK102CH-CT) $17.62

Check Chain & Pin Kit - Includes 1 Chain and 2 Clevis with pins and cotters. For most early models, pre-1965, category 1. (Part No: CBPN598A) $7.96

Drawbar Lock - For CAT I drawbars only (drawbars that are 1" thick x 2-1/2" width) . Prevents drawbar from rotating. (Part No: 49A29) $26.72

Drawbar Red - Drawbar, category I, 7/8" pins. 11 holes, 26" bar length. (Part No: 180485M1) $40.56

HITCH BALL 10000LB 2-5/16 - 2-5/16 BALL SIZE, 1-1/4STUD THREAD, 2-1/2 STUD LENGTH, 10000 LB MAX LOAD CAPACIRY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516114) $23.85

HITCH BALL 15000LB 2-5/16 - 2-5/16 BALL SIZE, 1-3/8STUD THREAD, 2-5/8 STUD LENGTH, 15000 LB MAX LOAD CAPACITY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516138_) $23.40

HITCH BALL 2000LB - 1-7/8 BALL SIZE, 3/4 STUD THREAD, 1-3/4 STUD LENGTH, 2000 LB MAX LOAD CAPACIRY, ONE CHROME HITCH BALL CLASS. (Part No: CHB17834) $12.30

HITCH BALL 3500LB - Hitch ball. 2" ball size, 3/4" stud thread, 1-7/8" stud length, 3500 lb. max load capacity, one/two chrome hitch ball class. (Part No: CHB234) $12.64

HITCH BALL 5000LB - Hitch ball. 2" ball size, 1" stud thread, 2-1/8" stud length, 5000 lb. max load capacity, two chrome hitch ball class. (Part No: CHB21) $14.44

HITCH BALL 5000LB 2-5/16 - Hitch Ball, 2-5/16" ball size, 1" stud thread, 2" stud length, 5000 lb. max load capacity, three chrome hitch ball class. (Part No: CHB25161) $20.52

LINCH PIN - Package of 10 linch pins. Pin diameter 5/16 inch, useable length 1 1/4 inch, Ring diameter 1 5/8 inch. Cold Forged. Enter 1 for package of 10. (Part No: DKP516) $4.00

LINCH PIN - LINCH PIN Package of 10 linch pins. 3/16" O.D. pin x 1-1/4" Long.***Enter 1 for package of 10** (Part No: DKP316) $3.90

LINCH PINS - Package of 10 linch pins, 7/16 dia. pin x 1-3/4 useable length, 1-5/8 dia. ring. Cold Forged. Enter 1 for package of 10. (Part No: DKLP91) $3.90

LINCH PINS - Package of 10 linch pins. Pin diameter 1/4 inch, useable length 1 1/4 inch. Cold Forged. Enter 1 for package of 10. (Part No: DKP14) $4.90

Quick Hitch, Category I - Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8" mounting pins and adapter bushings, 27-1/4" width, 3-1/2"x 3-1/2" beam. This is ONLY for tractors that have, a three point hitch already installed. An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $284.34

TOP LINK PIN - Category I top link pin, 3/4" pin diameter, 9-3/4" useable length, 10-5/16" overall length. Hinged assembly for Massey Ferguson. (Part No: P1012) $8.72

Top Link Assembly, OEM Style - Category 1-1, 17-1/4" length of center tube. Verify size before ordering. Replaces 1870075M9. (Part No: 184134M91) $65.85

Top Link Assembly, OEM Style - Category 1-1, 18-3/4" length of center tube. Verify size before ordering. Replaces 184078M91, 1869954M91. (Part No: 1690177M91) $45.06

Top Link Assembly, OEM Style - Category 1-1, 21-1/2" length of center tube. Verify size before ordering. (Part No: 184361M91) $65.85

Top Link Assembly, OEM Style - Category 1-2, 18-3/4" Length of center tube. Verify size before ordering. Replaces 3597172M91, 894376M1, 894376M91. (Part No: 194376M91) $67.20

Top Link Assembly, OEM Style - Category 1-2, 21-1/2" length of center tube. Verify size before ordering. (Part No: 894377M1) $57.70

Top Link Assembly, OEM Style - Category 2-2, 18-3/4" Length of center tube . (Part No: 893438M91) $67.20

Top Link Assembly, OEM Style - Category 2-2, 21-1/2" Length of Center Tube. Verify size before ordering. Replaces 3147681M91, 893439M91. (Part No: 1887285M91) $59.78

Top Link, Cat I - Top link, category I only, 16" body, 3/4" category I ball joints. Adjusts 20-1/2" to 29" overall. Dichromate plated center body. (Part No: 30533E91) $24.92

Top Link, Cat I and Cat II, Red - Top link, 16" body combination Category II tractor & Category I implement ends, Adjust 19-1/2" to 29-1/2" overall. Painted red. (Part No: JSA1200R) $32.31

Top Link, Cat I, Red - Top link, 24" body, 3/4" category I ball joints. Adjusts 29" to 39" overall. Painted red. (Part No: JSA1024R) $34.47

Top Link, Cat II, Red - Top link, 20" body, 1" category II ball joints. Adjusts 25" to 37". Painted red. (Part No: 30108E91*) $32.32

Top Link, Cat II, Red - Top link, 24" body, 1" Category II ball joints. Adjusts 29" to 41". Painted red. (Part No: JSA2024R) $47.14

Top Link, Hydraulic - Category I (3/4"), 18.5" to 26.0" length, 2.00" cylinder bore, 3/4" UNF port size. (Part No: B8106) $187.65

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Part No: DBL2) $27.98

Universal Stabilizer Chain Kit - Chain stabilizers, Turnbuckle & chain links adapt to any size 3-point hitch - usually used on larger tractors - VERIFY MEASUREMENTS. CLICK ON PICTURE FOR MEASUREMENTS. Move clevis up or down chain links; use turnbuckle for final adjustment. Packed & sold in pairs, less brackets. (Part No: SK102CH) $47.67

Hydraulic System
Clamp, Double Break-Away, Hydraulic - For use with S20-4 & S40-4 couplers. Quik-cover assembly HV4957 fits this clamp. (Part No: S42-4) $27.88

Coupler Flange - Optional drive flange for L601-9; 5/8" round bore with set screw 1/4" x 3/8" #SSH4-6. 2-1/4" spacing. Hydraulics: Drive flange; 5/8" round bore with set screw 1/4" x 3/8" #SSH4-6. 2-1/4" b-b. (Part No: L36-6) $75.51

Hydraulic Parts, Universal - Universal hydraulic parts such as hoses, filters, pressure gauges etc.. can be found in the Accessories and Universal parts section. (Part No: Hydraulic_Parts) $00.00

Hydraulic Valve Manifold - This 3 Spool Valve Allows Operator To Use Aux. Hydraulics at the same Time Without Valve Switching. Some Tractors may need slight modification on seat.Includes 2 elbows. Models from 1960 and later years. (Part No: 19833A92) $642.59

Valve - Valve for TS3200M. Single spool, 4-way, 3-position, spring loaded to neutral. No relief valve, no power beyond option. In & out ports 3/4", work ports 1/2" NPT. (Part No: TS200BA) $220.79

Implements
AXLE BOLT - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Part No: BH1317) $18.22

AXLE NUTS (5) - 5 Pack of Axle Nuts. Enter 1 for pack of 5. (Ref 4) Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Part No: 15622BH) $1.58

BLADE BOLT KIT - For rotary cutter blade used on rotary cutters. Please verify dimensions before ordering: A = 1 1/8-12 inch, B = 3 1/2 inch, C = 1 3/8 inch, D = 1 inch, E = 9/16 inch, F = 1/2 inch, G = 2 1/2 inch, H = 1.492 (for 1 1/2 Blade Hole), I = 1.12 inches. Contains (BH2500) hardware for 2 blades. (Part No: 63607) $16.66

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Part No: 170BH) $2.50

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Part No: 22) $8.28

Bush Hog Axle Spacer Bushing - Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600.Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken bearings (Ref #1-#11). (Part No: SPB40) $6.44

Caster Assembly - Tail wheel & hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2" diameter, 8" overall length, 7-1/4" to pin hole. New Style Tail Assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $172.49

Caster Assembly, Old Style - Tail wheel & hub assembly with grease fitting. 4 x 8 inch rim, 15 inch O.D. of wheel. Includes Wheel, Hub, Axle Bearing, and Bolt Assembly.OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600.Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken bearings (Ref #1-#11). (Part No: BH215) $103.86

Graphite Lubricant - Dry Graphite Powder, 5 lb container, used to lubricate planter seed channels. Recommended application rate: 2 oz per box. Typically treats 25-30 acres. (Part No: TP99500GP) $27.92

HUB with BRG CUPS - 4-bolt, 5" bolt circle & 3-5/8" wheel pivot hub with bearing cups (1" axel)(Ref #5). This part fits Caster Assembly (Part Number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Part No: BH1311) $44.15

Hub Assembly - Hub with bushings (3/4"), wheel bolts (4), and grease fitting. Center tube length 5". For rotary cutters: RB60 with new style 1-1/4" dia. caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Part No: 63813BH) $34.53

Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Part No: 221129) $40.23

Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Part No: 241100) $75.38

Round Bale Tine 43 Inches - Fully Hardened. (Part No: 241166) $95.34

Round Bale Tine 49 Inches - Fully Hardened. (Part No: 241162) $98.19

Round Bale Tine 55 Inches - Fully Hardened. (Part No: 241163) $107.04

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Part No: 30BH) $5.20

Tail Wheel Assembly - 6" x 9" tail wheel assembly with laminated tire, less hub. 4" pilot, 5 bolt holes, 5-1/2" bolt circle. 5-1/4" wide, 21" O.D., 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294) $125.98

Tail Wheel Assembly - 4" x 8" tail wheel assembly with laminated tire. 3-5/8" pilot, 4 bolt holes, 5" bolt circle, 3-3/4" wide, 15" O.D. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 & 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Part No: 500BH) $42.90

Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Part No: TP19000TP) $21.27

Lights
Halogen Work Light-Double Bulb - 12 volt lamp assembly, flood pattern, double bulb 55 watt halogen. Includes replaceable 55 watt halogen bulb. (Part No: L982-12V) $48.63

Headlight Ring - Rubber ring is 4 3/4 inches outside diameter and approximately 1 inch wide. Verify OEM part number. (Part No: 1027218M1) $10.65

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Part No: AA4667R) $19.56

Magnetic worklight Universal Mounting. - Can be placed anywhere there is a metal surface. 3-1/2" x 6" weather resistant steel body (black), glass lens, flood pattern, 140 ft. beam. Halogen bulb, 12 V, 55 watt, replaceable. 12 ft. cord with cigarette lighter plug. (Part No: L100MAG) $41.70

Portable Halogen Work Lamp - 3" x 5" sealed beam unit, 12 V, 50 watt, 4 amp. With handle & magnetic base. Projects flood beam pattern 50 ft. wide x 30 ft. long. Lamp is not legal for street use. (Part No: L200MAGH) $72.05

Safety Light Amber - 12 volt Amber Safety Light, 4 and a 1/4 dia., 3/8Dia by 5/8 mounting Stud.Does not include Flasher. (Part No: S.61357) $23.90

Work Lamp, HID, Flood Light - Universal high intensity discharge flood light, 35W Xenon H3 lamp, size 4.725" W X 4.330" H X 5.512" L, internal ballast, hardened glass lens, far longer life span than halogen 3000 to 3500 hours versus 280 to 400, higher lumen output 3200 lumens versus 700-1000 for halogen bulbs. (Part No: WL8500-E) $120.44

Work Light 12V With Switch - Work light, 12 volt, 3000 candle power, trapezoidal light pattern. On-off switch on back of light housing. Uses 4-1/2" diameter sealed beam lamp, L4411. (Part No: L408-12V) $28.08

Worklight 12 Volt - Red 12 Volt worklight with handle, on/off switch, swivels and rotates. (Part No: S.42792) $29.93

Worklight 12 Volt Black - 12 Volt worklight with handle, on/off switch, swivels and rotates. Mounting Holes measure 4 3.8 center to center. (Part No: S.67771) $31.65

Worklight Kit, 12 Volt, Chrome - 6 Inch Light Kit contains light bucket, bulb, chrome ring, 4 springs, socket mount, toggle switch, and 2 screws. (Part No: S.43378) $67.34

Miscellaneous
Air Cond Comp - New Air conditioning compressor, replacement for Frigidaire A-6 compressor. Includes 5.58" dia. clutch & dust cover, high pressure relief valve. With 12V coil at 10 Oclock, SAE thread. Less superheat switch (comes plugged with non-functional heat switch. For tractors that have air conditioning systems using the Frigidaire A-6 compressor already. (Part No: 1904014M92) $386.38

CabCAM Camera Observation System - When you need extra visibility around the farm or out in the field, a versatile camera observation system can give you the edge you need. Improve visibility at night with the twenty-eight infrared illuminator camera for excellent night vision. Reduces the need to turn around to check equipment. CabCAM Observation Kit Includes: Camera: Waterproof, CCD Color with Audio, 28 Infrared Illuminators Allow up to 32 feet of Visibility, Image Mirroring Function, Made to Withstand Off road Conditions. Monitor: 7 Color TFT LCD, Embedded Control Box for Direct Power Input for Cameras, AV2 Video Input for DVD/VCR etc., AV1 and AV3 Video Input to Hook Up to 3 Cameras. Accessories: AV Conversion Cable, Ball Swivel Mount Bracket with Adjustable Mounting Pad, Power Supply Cable, Earphones, Backshield, Cigarette-Lighter Power Adapter, Remote Control, Sunshield, AC Power Adapter, 20' and 65' Weatherproof Extension Cables. (Part No: CC7M1C) $339.62

Canopy - 60" wide x 65" long, moulded from virtually indestructable flexible U.V. stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through moulding. Available in green, white, orange, blue, or red. Please specify in comments section which color you need. Hardware to mount to your ROPS sold seperately.Add additional $150.00 to shipping due to weight and size, this item is shipped by truck. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257X) $402.16

Canopy Mounting Kit, 2 Post - Mounts the canopy to all our 2 post ROP frames except EMF1 (Hoop Type Frame). We need the measurement of the top of the ROP and the size of the ROP Tubing used. Put sizes in the comments section of the order form. (Part No: B6603) $70.84

Canopy Mounting Kit, 4 Post - Mounts the canopy to any 4 post ROP frame. (Part No: B6604) $61.16

Canopy Mounting Kit, Hoop Type - Mounts the canopy to CURVED OR SQUARE TOP Hoop Type ROP Frames up to 52" wide with leg thickness up to 4" x 2". (Part No: B6602) $103.07

Canopy, Small Tractors - 45" Wide x 60" Long Moulded from virtually indestructable flexible U.V. stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through moulding. Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold seperately. Add additional $150.00 to shipping due to weight and size, this item is shipped by truck. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257XSTD) $350.00

Deluxe Canopy, 3 Bow - Red. 3-Bow Deluxe Canopy. This sectional soft canopy with steel bows comes complete with cover and universal mounting brackets to fit on MOST fenders. Fits fendered wheel tractors, NOT including those with square fenders. 48 inch spread from Mounting brackets (41 inch spread at the top of canopy) Height is approx 31 inch. (Part No: RFC100R) $220.12

Deluxe Tractor Umbrella - Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel. All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material. Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering. (Part No: TU56-X) $145.07

HAND CLEANER GALLON - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Part No: PRM25218) $24.48

Oil System
Lucas Heavy Duty Oil Stabilizer (quart) - A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $12.93

PTO / Driveline
Coupler Repair Kit - Coupler repair kit, services all Hub City over-running couplers. Contains keys, roll pin, set screw, springs, spacer, & retaining ring. (Part No: CRK600) $35.87

Driveline Assembly - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor and implement yokes. 1333mm (52-1/2 inch) overall length, end of yoke to end of yoke. 1110mm (43-3/4) compressed length center to center of cross bore. Cross and bearing kit is 27mm 1.063 (1-1/16) bearing diameter x 74.6mm 2.940 (2-15/16). 1333mm (52-1/2 inch) overall length. ***VERIFY LENGTH BEFORE ORDERING*** (Part No: AB4111WY138) $164.92

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor & implement yokes. 1-3/8 6 spline Q.D. tractor yoke. 1-3/8 round bore with 1/2 pin hole implement yoke. 1300mm - (51 inch) overall length end of yoke to end of yoke. 1110mm (43-3/4) compressed length center to center of cross bore. Cross and bearing kit, 27mm - 1.063 (1-1/16) bearing dia. x 74.6mm - 2.940 (2-15/16) overall length (43-3/4) . Verify length before ordering. (Part No: AB4111WY) $183.74

Driveline Assembly with Yokes - AB4 series. Complete drive shaft assembly with shielding and tractor & implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-1/4 round bore with pin hole implement yoke. 1350mm (53) overall compressed length end of yoke to end of yoke. Cross and bearing kit, 27mm - 1.063 (1-1/16) bearing dia. x 74.6mm - 2.940 (2-15/16). Overall length 1350mm (53) ***VERIFY LENGTH BEFORE ORDERING*** (Part No: AB4111WY125R) $181.20

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 - 6 spline Q.D. tractor yoke, 1-3/8 - 6 spline ratcheting torque limiter iwth quick disconnect on implement end. 1372mm (54 inch) overall length end of yoke to end of clutch. 1110mm (43-3/4) compressed length center to center of cross bore. Cross and bearing kit 27mm -1.063 (1-1/16) earing dia. x 74.6mm - 2.940 (2-15/16). 1372mm (54) overall length ***VERIFY LENGTH BEFORE (Part No: AB4111K33) $278.82

PTO Adapter - PTO adapters are located under the PTO category in the Accessories & Universal Parts section. NOTE

PTO Safety Clutch, 40 HP - 1-3/8" 6 spline male and female ends, 6" dia., 40 HP capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Part No: B9164) $210.57

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Part No: JDV-02250) $24.00

Acrylic Hardener, 16oz - Lead free. For alkyd gloss tractor and implement enamel. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints. Mixes 1 to 2 gallons of unreduced paint. (Part No: TP12P) $44.60

Acrylic Hardener, 8oz - Lead free. For alkyd gloss tractor and implement enamel. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints. Mixes 2 quarts to 1 gallon of unreduced paint. (Part No: TP12HP) $27.96

Dakota Prep & Shine, Twin Pack - Kit inlcudes (1) 16.oz bottle Dakota Prep with spray nozzle, (1) 16 oz. aerosol can Dakota Shine, (2) scrub pads (1) light, (1) aggresive. (Part No: DS2PK) $38.48

Dakota Prep, 1 Gallon - Dakota Prep is a water-based and biodegradable cleaner that will remove wax buildup, grease, oxidation and grime from a variety of surfaces to renew paint to its previous luster. It is safe on many surfaces including painted surfaces, decals/vinyl lettering, plastics, fiberglass, clear coat finishes, aluminum, glass and rubber. (Part No: DP1G) $83.37

Dakota Shine, 1 Gallon - Dakota Shine is a unique and patented product that will restore the color, lustre and value to faded and oxidized surfaces like paint, decals, plastics, fiberglass, engine compartments and more. The ingredients are designed to penetrate the surface to rejuvinate the pigments to their original, lime-new appearance. No mixing required, quick dry time and no overspray lines to buff out. Used in conjunction with Dakota prep for best results. (Part No: DS1G) $138.26

Paint, Aluminum, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP312GAL) $42.53

Paint, Aluminum, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP312QT) $24.74

Paint, Aluminum, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP312SP) $42.52

Paint, Clear Coat, 1 Gallon - From Tisco providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. (Part No: TP447GAL) $71.91

Paint, Clear Coat, 1 Quart - From Tisco providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. (Part No: TP447QT) $29.91

Paint, Clear Coat, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From Tisco providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. (Part No: TP447SP) $51.68

Paint, Dark Gray, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** For TO20, TO30 1946-54 and implements before 1955. From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP230SP) $42.52

Paint, Gloss Black, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP550GAL) $42.24

Paint, Gloss Black, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP550SP) $42.52

Paint, Gray Primer, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP2700GAL) $42.24

Paint, Gray Primer, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP2700QT) $18.69

Paint, Gray Primer, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP2700SP) $42.61

Paint, Industrial Yellow, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP540GAL) $109.15

Paint, Industrial Yellow, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP540LF-QT) $34.84

Paint, Light Gray, 1 Gallon - From TISCO, providing OEM quality. TO35 Sheet Metal 1954-56 and implements after 1954. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP235GAL) $59.59

Paint, Light Gray, 1 Quart - From TISCO, providing OEM quality. TO35 Sheet Metal 1954-56 and implements after 1954. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP235QT) $27.11

Paint, Light Gray, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** TO35 Sheet Metal 1954-56 and implements after 1954. From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP235SP) $51.18

Paint, MF Red, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP300GAL) $42.24

Paint, MF Red, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP300QT) $24.74

Paint, MF Red, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP300SP) $42.52

Paint, MH Red, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP340GAL) $61.83

Paint, MH Red, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP340SP) $51.68

Paint, Metallic Flint Gray, 1 Gallon - From TISCO, providing OEM quality. Used on TO35, F40 castings 1956-60. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP320GAL) $60.53

Paint, Metallic Flint Gray, 1 Quart - From TISCO, providing OEM quality. Used on TO35, F40 castings 1956-60. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP320QT) $24.12

Paint, Metallic Flint Gray, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** For models TO35, F40 castings 1956-60. From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP320SP) $42.52

Paint, Satin Black, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP225GAL) $45.50

Paint, Satin Black, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP225QT) $25.92

Paint, Satin Black, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP225SP) $42.52

Paint, Silver Mist Gray, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP750GAL) $65.42

Paint, Silver Mist Gray, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP750QT) $24.08

Paint, Silver Mist Gray, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP750SP) $51.68

Paint, Soft Black, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP200GAL) $53.93

Paint, Soft Black, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP200SP) $42.52

Paint, Straw Yellow, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP345GAL) $121.70

Paint, Straw Yellow, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP345QT) $41.15

Paint, StrawYellow, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP345SP) $51.68

Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Part No: BL116GAL) $65.92

Slip Resistant Coating - Quart can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 19 to 25 square feet. (Part No: BL116QT) $27.81

Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Part No: BL116KIT) $95.63

Tire Paint, Black - Black tire paint (1 Quart)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It won't rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is a concentrate which you dilute one-to-one with water. A little goes a long way! (Part No: E844Q) $21.00

Tire Paint, Black - Black tire paint (1 Quart)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It won't rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is a concentrate which you dilute one-to-one with water. A little goes a long way! (Part No: E844Q) $21.00

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It won't rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Part No: E844R) $39.95

Seats
Pan Seat, Universal - 17 inch wide Gold zinc plated, 3-1/2" center to center on mounting holes, 1/2" by 1/2" center square. (Part No: B1865) $37.24

Seat Belt - Universal Seat Belt. Can be adapted to many tractors. (Part No: RSB22) $36.67

Seat Belt, Universal - Seat belt, universal 2-point static adjustable belt. Fits TS1110 seats. (Part No: TS1110BELT) $23.10

Seat Cover (Red and Yellow) - Tie-on for 19 inch wide pan seat. For Tractors that have a Red and Yellow color scheme. (Part No: XYFR30RY) $30.00

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft & lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up & angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Part No: TS5056V) $1294.75

Seat, Industrial - Seat assembly. Durable one-piece stamped steel pan. (Yellow) Leatherette upholstery, Dimensions: 18" W, 19" H, 21" D. (Mounting holes 9" W x 9-3/4" D). Fits several Commercial Turf/Mowers, Utility trucks, Fork Lifts, Skid Steer Loaders, Pavers, Sweepers, Construction Equipment, Utility tractors, Row crop tractors, Loader backhoes, Etc. (Part No: TS1110INDY) $98.77

Seat, Universal - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. (Part No: TS1050ATSP) $101.46

Seat, Universal - BLUE Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE. (Part No: TS1060ATSP) $93.40

Seat, Universal - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK. (Part No: TS1075ATSP) $93.40

Seat, Universal - Seat assembly, Black leatherette upholstery, Dimensions: 18-3/4 W, 19 inches H, 21 inches D. Non-suspension type with slide track for forward/rear adjustment (Slide track 9 inches W x 11-1/4 D). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify Seat and slide track dimensions listed above before ordering. Weight 33 lbs. (Part No: TS1110BK) $106.23

Seat, Universal - Seat assembly, Blue leatherette upholstery, Dimensions: 18-3/4 W, 19 inches H, 21 inches D. Non-suspension type with slide track for forward/rear adjustment (Slide track 9 inches W x 11-1/4 D). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify Seat and slide track dimensions listed above before ordering. Weight 33 lbs. (Part No: TS1110BL) $109.62

Seat, Universal - Seat assembly, Yellow leatherette upholstery, Dimensions: 18-3/4 W, 19 inches H, 21 inches D. Non-suspension type with slide track for forward/rear adjustment (Slide track 9 inches W x 11-1/4 D). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify Seat and slide track dimensions listed above before ordering. Weight 33 lbs. (Part No: TS1110YL) $106.23

Seat, Universal INDUSTRIAL with SLIDES - Seat, universal, non-suspension style seat assembly with slide track for forward/rear adjustment. Slotted base for adjusting slide tracks side to side 4" to 10-1/4". Black leatherette upholstery, vacuum formed and watertight for use in all weather conditions. (Part No: TS1036IND) $70.15

Tie-On Seat Cover - Grey, 19 inches wide. Deluxe with 2 inches of foam. This fits a PAN seat. (Part No: R2600) $30.00

Universal Seat - Black leatherette upholstery. Narrow seat for compact tractors. Internal suspension, weight adjustable. 5 position adjustable base. Special slotted base for mounting. Seat is 15" wide, 17" long, 19" high to the back of the seat. (Part No: TS1015) $172.58

Universal Seat - **YELLOW** Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Part No: TS1040ATSP) $97.65

Sheet Metal / Body Parts
2 Hour DVD - The How To's of Sheetmetal Repair - This DVD is intended to show how to restore sheetmetal on your tractor. A John Deere tractor is used in the demonstrations but the information is useful for all tractors. You can use this DVD as a tool to evaluate what work, cost, and time it is going to take to restore the tractor you own or are looking to purchase. 118 minutes. (Part No: RCR06-DVD) $24.00

Bumper With Bolts - Bumper assembly, mounting arms NOT included. Additional shipping charge of $20.00 due to weight. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: BU10211R) $184.46

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Part No: R0140) $30.09

DZUS Fasteners Kit - Universal Set of 5 fasteners. 1/4 Turn Fasteners. For 13/32 inch holes, Head Diameter is 11/16, springs are 1 7/8 inch in length. Verify size before ordering. (Part No: DZUS2) $16.00

SAFETY STEP KIT - Traction Where you need it. Great for use on tractor and combine steps, trailers, grain bin ladders and more. Kit includes 1 pint safety base and safety grit. (Part No: SSK14011) $51.96

Toolbox - Universal style of 11 inches long, 4 inches wide and 4.5 inches tall. Must drill mounting holes to match your tractor. (Part No: ABC308) $37.50

Toolbox - Universal Toolbox 15 1/2" X 4 3/4" X 4 1/4". Comes Primed ready to prep and paint. (Part No: R2685) $29.40

Toolbox, Fender Mount - This is an aftermarket toolbox designed to mount easily on the fender of most agricultural and industrial tractors. This is an aftermarket item, unlike any original toolboxes, and is meant for working tractors in need of a good toolbox. 18 inches long, 3-5/8" wide and 4-1/2" deep. (Part No: TB100FM) $43.86

Steering
Steering Wheel Spinner, Bare Aluminum - Comes with mounting hardware. (Part No: R3275) $10.00

Steering Wheel Spinner, Black - Comes with mounting hardware. (Part No: R3276) $11.70

Steering Wheel Spinner, Blue - Comes with mounting hardware. (Part No: R3279) $11.70

Steering Wheel Spinner, Green - Comes with mounting hardware. (Part No: R3278) $11.70

Steering Wheel Spinner, Orange - Comes with mounting hardware. (Part No: R6323) $11.70

Steering Wheel Spinner, Red - Comes with mounting hardware. (Part No: R3277) $11.70

Steering Wheel Spinner, Yellow - Comes with mounting hardware. (Part No: R3280) $11.70

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16" x 5/8" x 5/8", 1 15/16" x 3/4", 3/4", and 1 3/8" x 1" x 1/2". (Part No: TIERODBOOTS) $15.30

Tools
*Combination Wrench Set - 22 pieces SAE/Metric. Polished chrome vanadium steel. Metric: 9, thru 19 mm. SAE: 1/4 thru 7/8. Comes with a durable plastic rack for handy storage. LIFE TIME UNLIMITED WARRANTY. (Part No: W1069) $29.99

Adjustable Cylinder Hone Replacement Stones, Coarse - Set of three 4" coarse textured stones with cotter pins for 900542 cylinder hone. (Part No: 900563) $17.48

Adjustable Cylinder Hone Replacement Stones, Fine - Set of three 4" fine textured stones with cotter pins for 900542 cylinder hone. (Part No: 900556) $17.48

Adjustable Cylinder Hone Replacement Stones, Medium - Set of three 4" medium textured stones with cotter pins for 900542 cylinder hone. (Part No: 900549) $17.48

Adjustable Engine Cylinder Hone - Resurfaces cylinder walls so new rings will seat and eliminate minor cylinder wall imperfections. 2" to 7" diameter range with adjustable tension settings to control the cutting action. Features flexible shaft that will fit any variable speed drill and replaceable 4" stones. Medium texture stones included. Stone replacement part numbers are (900556)Fine textured stones, (900549) medium textured stones and (900563) coarse stones. (Part No: 900542) $38.37

Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Part No: S.29891) $19.95

Chain Binder - 1/4" chain binder, 2600 pound load limit. (Part No: LL104) $36.74

Chain Binder - 3/8" chain binder, 5400 pound load limt. Use with either 5/16" or 3/8" chain. (Part No: LL105) $41.70

Chain Binder - 1/2" chain binder, 9200 pound load limit. Use with either 3/8" or 1/2" chain. (Part No: LL106) $78.11

Combination Wrench Set - 11 pieces. Sae sizes 1/4 to 7/8. Chrome vanadium steel construction. Handy storage rack. LIFETIME UNCONDITIONAL WARRANTY. (Part No: W1061) $21.00

Cotter Pin Assortment - 150 Pieces. Contains sizes of 1/8x2, 5/32x2 1/2, 3/16 x 3, 1/4 x 2, 1/4 x 3, 5/16 x 2 1/2. All in a convenient re-sealable plastic case. (Part No: W5206) $12.48

Cotter Pin Assortment, Small - 560 piece assortment of 1/16" x 1", 3/32" x 1", 3/32" x 1-1/2", 1/8" x 1-1/4", 1/8" x 2", 5/32" x 2-1/2" all in convenient re-sealable plastic case. (Part No: W5205) $9.40

Diesel Compression Test Kit - Complete kit with case. 0 to 1000 PSI Gauge (0-700kPA). Includes 9 adapters for popular Domestic, Asian and European vehicles. Will fit the following thread sizes: 24 x 2.00, 12 x 1.25, 10 x 1.25, 10 x 1. Tests compresssion through both flow plug and injector holes. Gauge accuracy +/- 2 percent. (Part No: W89731) $59.95

Digital Calipers, Stainless - High quality hardened stainless steel digital caliper. calculates measurements up to 6" with SAE and METRIC conversions. Includes convenient carrying case and spare battery. (Part No: CAL6) $36.11

Engine Compression Tester - Checks cylinder compression up to 300 PSI. Fits 14 and 18mm spark plug threads. Equipped with air-hold valve and gauge reset button. 11 inch flexible rubber hose. Complete with instructions. (Part No: W80579) $32.48

GREASE GUN - GREASE GUN-Pistol handle grease gun uses standard 11" grease cartridge. Develops 8000 lbs pressure. Pistol design makes it convenient to use. (Part No: GG3121) $28.88

GREASE GUN - Spring fed 11" barrel grease gun. Uses standard 11" grease cartridge. Lever handle develops 10, 000 lbs of pressure. (Part No: GG1080) $26.74

GREASE GUN - HEAVY DUTY Grease gun, ultimate gun designed specifically for heavy-duty use and is built to take extreme punishment. (Part No: GG11142) $35.16

GREASE GUN CLAMP - Clamp holds all 2-1/4" diameter barrel hand guns. Bolts or screws anywhere thru hole in bracket base. (Part No: GC102) $12.44

GREASE GUN POWERLUBER 14.4V BATTERY - Battery, Replacement 14.4 Volt NI-CAD rechargeable battery for use with GGPL1442B & GGPL1444B PowerLuber grease gun. (Part No: GGPL1401) $109.95

GREASE GUN POWERLUBER 14.4V with CASE 1 BAT - Grease gun 14.4 Volt PowerLuber, Professional two-speed cordless rechargeable grease gun. Complete with 110-volt fast charger, 14.4 volt NI-CAD rechargeable battery, 30" flex hose with spring guard & custom carrying case to hold two rechargeable batteries. (Part No: GGPL1442B) $270.05

GREASE GUN POWERLUBER 14.4V with CASE 2 BAT - Grease gun 14.4 Volt PowerLuber, Professional two-speed cordless rechargeable grease gun. Complete with 110-volt fast charger, (2) 14.4 volt NI-CAD rechargeable batteries, 30" flex hose with spring guard & custom carrying case to hold two rechargeable batteries. (Part No: GGPL1444B) $376.87

GREASE HOSE 12 INCH - 12 flexible grease gun hose.Sold in quantities of 2, PRICE IS FOR EACH. (Part No: G115) $10.86

GREASE HOSE 18 INCH - 18" flexible grease gun hose.Sold in quantities of 2, PRICE IS FOR EACH. (Part No: G118) $9.90

Hair Pin Assortment - 150 pieces. Includes 6 different sizes from 1 3/16 Length to 2 15/16. All in a convenient re-sealable plastic case. (Part No: W5210) $8.32

Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Part No: S.58474) $249.90

Hobby Tool Kit - With Carrying Case. Complete Knife kit with two handle styles. Also comes with 3 inch caliper, tweezers, precision screwdriver and 28 blades. (Part No: W1709) $23.74

Hose Clamps Assortment - 26 pieces. Includes sizes of: 5/8, 7/8, 1, 1 1/16, 1 1/4, 1 1/2 inch. All in a convenient re-sealable plastic case. (Part No: W5348) $8.06

MULTI TESTER - Compact size meter for testing volts (up to 500 Volts), OHMS and AMPS. Includes color coded test probes and instruction booklet. Uses AA batteries, not included. (Part No: ETA66420) $24.76

Main Seal Installer/Remover - Removes and installs upper rear main seals on many engines without removing engine or crankshaft. Contains corkscrew removal tool, T-handle and wire with clip for pulling new seals into place, 2 extra clips. (Part No: W84019) $7.10

O-Ring Assortment - 407 pieces. Includes 32 sizes from 1/4 O.D to 2 1/4 O.D. All in a convenient re-sealable plastic case. (Part No: W5202) $16.36

Piston Ring Compressor - Use to install pistons. Positive compression and adjustable friction brake. Includes instructions. Band diameter from 3.5 to 7 inches (88 to 177mm). (Part No: W80573) $18.12

Piston Ring Groove Cleaner - Cleans carbon and deposits from ring grooves. Includes two 5 cutter wheels for a total of 10 groove cleaning sizes: SAE: 1/16, 5/64, 3/32, 3/16 and 1/4. Metric: 1.5, 1.75 and 2 mm. (Part No: W80576) $18.26

Rotary Tool Kit - 80 Pieces. Hand held rotary tool. Turns at 1600 rpm. Contains cut off wheel mandrel, polishing cloth wheels, mandrel for polishing cloths, carbide burr, collets, sanding drums and sleeves, buffing wheels, dressing stone and drill bits. Great for cutting, grinding, polishing, sharpening and drilling. (Part No: W50083) $19.00

Rubber Grommet Assortment - 125 pieces in 18 various sizes from 1/8 x 9/32 to 1 inch. All in a convenient re-sealable plastic case. (Part No: W5214) $9.38

Screwdriver Set - 30 pieces. Contains 7 screwdrivers 1/4 to 6 inch, a magnetic bit driver, 6 precision screwdrivers, 14 power bits. All contained in a Plastic Rack (Part No: W1718) $23.08

Spring Assortment - 200 pieces. Includes compression type sizes from 9/32 x 1/2 to 7/32 x 1 1/2, extension type from 13/64 x 13/16 to 11/32 x 1 7/16. (Part No: W5200) $7.98

Step Drill Bit Set - 3 Pieces. Titanium Nitride Coated high speed steel. 1/4 inch shank. Drills holes up to 1 inch. For use with metal, wood or plastic. Starts on contact, no center punch required. Automatically deburrs holes as you drill. (Part No: W9003) $17.20

T-Handle Hex Key Set - 10 Pieces (SAE). High quality carbon steel shafts. Black oxide finish resists corrosion. PVC T-handle grips for added torque and comfort. Sizes: 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16 and 3/8 inch. Comes with hand storage rack (mountable). (Part No: W80274) $19.94

Torque Wrench - Micrometer 1/2 inch drive adjustable torque wrench. Chrome plated alloy steel. Reversible ratchet head. SAE and Metric Scale. 10 to 150 lb torque range. 1 lb graduations. (Part No: M200DB) $34.40

Valve Spring Tool - Compresses springs without removing head. Adjustable cam handle keeps tool correctly adjusted for entire job. Remove lever and turn with socket in confined areas. (Part No: W80567) $31.24

WIRE STRIPPER 4-WAY - 4-way wire stripper/crimper tool, cuts wire 10 gauge and lighter. Strips wire 10-22 gauge, crimps solderless terminals. (Part No: ETA66223) $9.88

Winch Remote, Wireless - Used with winch sets 3013-0002 and 3013-0001. (Part No: 3013-0003) $37.50

Winch Set, 2500 Lb - Universal 12 volt with Push button switch. Wireless remote available as p/n 3013-0003. (Part No: 3013-0002) $129.95

Winch Set, 2500 Lb - Universal 12 volt with Hand held remote. (Part No: 3013-0004) $119.95

Winch Set, 3500 Lb - Universal 12 volt with Push button switch. Wireless remote available as p/n 3013-0003. (Part No: 3013-0001) $149.95

Winch Set, 3500 Lb - Universal 12 volt with Hand held remote. (Part No: 3013-0005) $129.95

Wire Terminal Assortment - 160 piece set. Contains 19 popular sizes and types of wire terminals. All in a convenient re-sealable plastic case. (Part No: W5213) $15.48

Woodruff Key Assortment - 80 pieces. Includes 10 each of: 3x5x13 mm, 3x6.5x16 mm, 4x5x13 mm, 4x6.5x16 mm, 4x7.5x19 mm, 5x7.5x19 mm, 5x9x22 mm, 6x9x22 mm. All in a convenient re-sealable plastic case. (Part No: W5341) $11.26

Tractor Manual Search - Yesterday's Tractor Co.

Wheels
Front Tractor Tires - We are now offering Front Tractor Tires! Click on the picture to view different tread designs. Tires that have a corresponding letter are available. Tread designs vary depending on size and availability. Allow 7 to 10 business days for delivery. Call for shipping cost, pricing and tire availability 1-800-853-2651. Please have your tire size available. Do not put this part in basket. NOTE

Rear Rim Carriage Head Bolt and Nut - 2.5 length, 5/8 diameter FF Carriage Head Bolt with nuts. PRICED EACH. **Minimum order is quantity of 6. (Part No: HB250) $3.25

Rear Tractor Tires - We are now offering Rear Tractor Tires! Click on the picture to view different tread designs. Tires that have a corresponding letter are available. Tread designs vary depending on size and availability. Allow 7 to 10 business days for delivery. Call for shipping cost, pricing and tire availability 1-800-853-2651. Please have your tire size available. Do not put this part in basket. NOTE

Rim 10X28 - Rim, 10 x 28 demountable rim with 6 loop clamps. Painted aluminum color. Add $25.00 extra shipping due to weight. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: 180863M91) $124.83

Rim 11X28 with 6 Loop Clamps - Rim, 11 x 28 demountable rim with 6 loop clamps. Painted aluminum color. Shipped via truck -Add $30.00 extra shipping per rim due to weight. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: 535450M91) $136.86

Rim, 12X24 - Rim, 12 x 24 demountable rim for 13 x 24 or 14 x 24 tires. Add $15.00 extra shipping due to weight. 6 Loops, these measure 20 1/4 inches center-to-center across from one another. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: 535454M91) $147.72

Stop Body Rim - Stop body, for power adjust rims 535452M91, 535453M91, & 1687615M91. Use with double ramp clamp 3615259M1 or 1755057M2. Replaces 227609M1. Minimum order quantity is 2 price is for 1. (Part No: 503676M1) $28.70

TIRE GAUGE - Gauge has special oiling & pump-out feature to clean out anti-freeze. Calibrated 4-50 pounds. (Part No: T9350) $15.48

TIRE GAUGE DIAL - Precision bourdon tube (non-plunger), dial style tire gauge: 60 pound. Reading in 1 pound calibrations. Individual "see-thru" vinyl permanent container pouch. Not for use with liquid-filled tires. (Part No: T600XG) $17.16

Tire Gauge, Heavy Duty - Accugage measures up to 60 lbs. Comes with braded flexible hose, bleed valve, unbreakable crystal and rubber boot. Breass geared movement. Bourdon tube design (not plunger type). (Part No: B1SB6599) $42.82

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It won't rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Part No: E844R) $39.95

Tire Paint, Black - Black tire paint (1 Quart)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It won't rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is a concentrate which you dilute one-to-one with water. A little goes a long way! (Part No: E844Q) $21.00

Tire Tube 24 Inch - For 7.5, 8.3, 9.5 x 24 inch tires. (Part No: WHS060) $37.60

Tire Tube 24 Inch - For 11.2, 12.4 x 24 inch tires. (Part No: WHS059) $51.30

Tire Tube 28 Inch - For 11.2, 12.4 x 28 Inch Tires. (Part No: WHS058) $56.55

Tire Tube 28 Inch - For 13.6, 14.9 x 28 Inch Tires. (Part No: WHS061) $79.45

Tire Tube 32 Inch - For 9.5 x 32 Inch Tires. (Part No: WHS062) $56.95

Tire Tube 34 and 36 Inch - For 11.2 or 12.4 x 34 Inch Tires and for 11.2 or 12.4 x 36 Inch Tires. (Part No: WHS063) $59.90

Tire Tube 38 Inch - For 11.2, 12.4 x 38 Inch Tires. (Part No: WHS064) $65.25

Tire Valve Fluid Adapter - FOr ballast. (Part No: S.61167) $27.90

Tire and Tube - 400x12 3 Rib Tire with tube. (Part No: 400x12-3) $74.22

Show CategoriesShow all TO30 Parts
Manuals
If you will be servicing or maintaining your tractor, we highly recommend that you have a manual to refer to. We searched the tractor manual database and found the following items. They may or may not apply to your tractor, please read the descriptions carefully. Our search engine isn't perfect... yet!
Ferguson TO30 Manuals
TO30 Sherman Transmission - Over-Under Tran, Forward-Reversing Tran, Live PTO Kit Service Manual 42 Pages (Part No: FO_SHERTRAN_SV) $14.95

TO30 Service Manual 196 Pages (Part No: 55-FDSM) $24.95

TO30 Parts Manual 135 Pages (Part No: MH_TO20_PT) $19.95

TO30 Operators Manual 50 Pages (Part No: MH-O-MFTO30) $20.95

TO30 Implements - 40 Items Parts Manual 702 Pages (Part No: MH-P-TO20&30IM) $102.95

TO30 Implements - 10 Items, Including Plows, Disc, Grain Drill, .Mower, Rake,Hydraulic Hookup on Tractors Operators Manual 138 Pages (Part No: MH_TO20&TO30IMP_OP) $29.95

TO30 Sherman #49 Backhoe Attachments Service Manual 54 Pages (Part No: FO-SOP-SHER54A) $20.95

TO30 Sherman #54A100 Backhoe Attachments Service Manual 54 Pages (Part No: FO-SOP-SHER54A) $20.95

Miscellaneous Related Items
Tune-up DVD
Massey-Ferguson 135 - Includes rebuilding the carburetor and distributor, oil and filter change, brake adjustment, troubleshooting and more. Step-by-step instruction, with information pertaining to the MF 35, 50 and TO30 with 4-cyl Continental Z Series Engines (Part No: JDV-02150) $24.00

Rebuild DVD
Massey-Ferguson 135 - Shows how to completely rebuild the tractor's engine. You'll see the engine disassembled down to the bare block and then rebuilt step-by-step in an easy-to-follow format. With information pertaining to the MF35, MF50, MF150, TO20, TO30, TO35, F40, MF202, MF204, MF2135 & MF50 with 4-cyl Continental Z Series Engines Engine Rebuild (Part No: JDV-02050) $24.00

Hat
Red Massey Ferguson hat - 65% cotton, 35% polyester, low-fitting 6-panel hat. (Part No: MFSR) $13.95

Massey Ferguson red hat - With black brim, 6-panel pro style cap with brass buckle size adjuster. (Part No: MFRB) $13.95

Massey Harris Red hat - Round logo sewn on for durability, red hat with matching brim. (Part No: MHSR) $13.95

Massey Harris Red Mesh hat - 6 panel low profile red mesh hat, plastic snap size adjuster, 65% cotton, 35% polyester, 100% nylon back. (Part No: MHRM) $13.95

Massey Harris Flame hat - Red and yellow flames on black 6-panel hat. (Part No: MHFL) $19.95

Call 800-853-2651 to Order
Or Click the "Add to Cart" Button

[Show Categories]   [Show all Ferguson Models]   [Printer Friendly]  





PayPal


Customer Service
Monday - Friday
10:00-6:30pm
EST

Order online
anytime!







Your Shopping
is Secure

  

YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

Copyright © 1997-2014 Yesterday's Tractor Co.
Antique Tractor Headquarters
All Rights Reserved

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.