FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Case 740 Tractor Parts

[Categories] [All Case Models] [Print]

Cooling System

Thermostat, 160 Degrees - This is a 160-degree thermostat. Used on Case models Super 400, 400, 401, 402, 403, 405, 410, 411, 412, 413, 414, 415, 420, 425, 700, 701, 701B, 702, 702B, 703, 703B, 705, 705B, 710, 710B, 711, 711B, 712, 712B, 713, 713B, 715, 715B, 725B, 730, 730 Comfort King, 730 Draft-O-Matic, 730CK, 731, 732, 733, 734, 740, 741, 742, 743, 744, 800, 800B, 801, 801B, 802, 802B, 803, 803B, 805B, 810, 810B, 811, 811B, 812, 812B, 813, 813B, 815, 815B, 830, 830 Comfort King, 830 Draft-O-Matic, 831, 832, 833, 840, 841, 842, 843, 900, 900B, 910, 910B, 920B. Replaces 1002521M91, 185201M2, 226372, 228543, 70226372, 70228543, 830873M93, A11493, A28114, TG10608 (Item #: 150677, Ref: 226372) $23.40

Water Pump - Less pulley. For tractor models 730, 740, 830, 840 Replaces OEM numbers A48368, A21459, A153454. 3.055 inch Impeller, Shaft Extends 2 1/2 inch Beyond Bearing. (Item #: 111833, Ref: 939629) $140.00

Electrical System

Electronic Ignition Conversion Kit, 12 volt negative ground - 4-cylinder engines.For 470, 570 with G148B, G159; 730, 740, 840, 680CK with A251G, A284G; 830 with A-284G; 770, 870 with A251BG, A301BG. Electronic ignition conversion kit, replaces points and condenser with an electronic module. Use on 12 volt negative ground system with a Prestolite distributor. MUST ALSO REPLACE CAP (Part # AL165) and ROTOR (Part # AL150) both available from an auto parts store. If you have a dust cap, you are required to enlarge the hole for the new rotor to fit. Fits the following distributors IBT-4702, IBT-4709, IBT-4707, IBT-4706, IBT-4705, IBT-4701, IBT-4501, IBT-4405, IBT-4404, IBT-4403A, IBT-4105A, IBT-4106A, IBT-4106C, IBT-4402, IBT-4001G, IBT-4102A (Item #: 105090, Ref: 1542) $160.00

Electronic Ignition Conversion Kit, 12 volt positive ground - For 470, 570 with G148B, G159; 730, 740, 840, 680CK with A251G, A284G; 830 with A-284G; 770, 870 with A251BG, A301BG. Electronic ignition conversion kit, replaces points and condenser with an electronic module. Use on 12 volt positive ground system, use with Prestolite distributor using the "A" type rotor which is "T" Shaped. CAP (Part # AL165) and ROTOR (Part # AL150) both available from an auto parts store. If you have a dust cap, you are required to enlarge the hole for the new rotor to fit. (Item #: 108152, Ref: 1542P12) $155.00

Electronic Ignition Conversion Kit, Wico DB distributor # X30091E - 12 Volt Negative Ground. For 730, 830, 740, 840, 900, 930, all with Wico DB distributor # X30091E. Pertronix Electronic Ignition Conversion Kit. (Item #: 108153, Ref: WO141) $166.00

Fuse Holder - Mounts on 5/8 inch diameter hole. 2 spade connectors. Replaces: 578489, cap: A10958, A22874, A8006, D122429, D23834, D49077, F63019, G44876, T39463 (Item #: 112273, Ref: 376852R91) $10.40

Neutral Safety Starter Switch - Built to OEM specification, this Neutral Safety Starter Switch has the following measurements: 35 amp at 12 Volt, 20 amp at 24 Volt, 9/16-18 thread UNF-2A, 5/16 inch stem length, 1-1/8 inch hex head. Used on Case: 430, 530, 630, 730, 930, 1030, 770, 830, 870, 970, 1030 Comfort King, 1031, 1032, 1070, 1090, 1170, 1175, 1270, 1370, 2470, 940, 830 Comfort King, 732, 743, 832, 730 Comfort King, 843, 831, 932, 930 Comfort King, 842, 731, 734, 931, 733, 833, 941, 431, 435, 441, 445, 531, 535, 540, 541, 545, 631, 632, 634, 640, 641, 642, 644, 740, 741, 742, 744, 840, 841. Replaces G44873, A20990, 716945, 80716945 (Item #: 178501, Ref: A20990) $20.20

Engine Bearings

Camshaft Bearings - Standard Camshaft Bearings for 2.247 journal camshaft used in tractor models 400, 680, 700, 730, 740, 800B, 810, 830, 840 all gas or diesel engines. Replaces A23577. Engines: Case A267DB, A251B Gas, 267BD, 336BD, A301D, 301B (Item #: 106142, Ref: 811224) $65.00

No
Picture
Main Bearing Set - Less Thrust Washers Available in STD, .010, .020, .030 For 400 Super, 680CK, 700, 730, 740, 800 with A267D Diesel Engine (Item #: MS-1497P) $97.00

No
Picture
Rod Bearing, STD - Price is for Bearings for 1 Rod. For tractor models 1000, 1010, 1030, 1060, 1070, 1090, 1150, 1150B, 1150C, 1160, 1170, 1175, 1200, 1270, 2290, 2294, 700B, 730, 740, (750 SN# 7070351 and below), 770 4 cylinder 800B, 830, 850, 930, 970, (Super 400 diesel SN# 8106131 and up), W10, W10E, W12, W18, W20, W7, W7C, W8, W8E, W9, W9A, W9E. (Item #: 106114, Ref: A43173) $17.70

Engine Gaskets

Conversion Gasket Set - This Conversion Gasket Set does not include Case-o-matic and Draft-o-matic pan gaskets. It is used on: (400 Super with A267D 4-Cylinder Diesel Engine and Standard Clutch, (680CK with A267D 4-Cylinder Diesel Engine with Standard Clutch) (700 with A267D 4-Cylinder Diesel Engine with Standard Clutch), (730 with A267D 4-Cylinder Diesel Engine with Standard Clutch), (740 with A267D 4-Cylinder Diesel Engine with Standard Clutch), (800 with A267D 4-Cylinder Diesel Engine with Standard Clutch), (830 A301D 4-Cylinder Diesel Engine), (840 A301D 4-Cylinder Diesel Engine) (Item #: CS3273Y) $96.78

Conversion Gasket Set - For Case tractor models 400 (s/n 8253500-earlier), 730 (s/n 8253500-later), 740 (s/n 8253500-later), 830 (s/n 8253500-later), 840 (s/n 8253500-earlier), Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W9A, 680CK, Compatible with Case Engine (s) G251, G284, Includes crank seals, Contains all gaskets necessary to complete an overhaul that are not included in the head gasket set, (Item #: 106149) $327.15

Conversion Gasket Set - For Case tractor models 400 (s/n 8253500-earlier), 730 (s/n 8253500-earlier), 740 (s/n 8253500-earlier), 830 (s/n 8253500-earlier), 840 (s/n 8253500-earlier), Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W9A, 680B (s/n 9103966-earlier), 680CK, 750 (s/n 7070350-later), 850 (s/n 7073468-earlier), Compatible with Case Engine (s) D267 (standard transmission), D301 (standard transmission), Includes crank seals, Contains all gaskets necessary to complete an overhaul that are not included in the head gasket set, (Item #: 106150) $117.00

No
Picture
Engine Overhaul Gasket Set - For tractor models 400, 700, 730, 740 and 800B. Overhaul set equipped with Std. clutch and A267 or A267D diesel engines. NOTE: If ordering for a Case 800B, also order 2 of A9235 head gasket. (Item #: 183865, Ref: FS6735) $469.00

Front Crankshaft Seal - This front crankshaft oil seal has a 2.625 inch Inside Diameter, a 3.628 inch Outside Diameter and is .433 inch wide. Replaces: A157044, A23433, A24715, A27838, A40349, A57342, A62049, O3866AB, O8583AB, O9708AB, T34263 (Item #: 106145, Ref: A57342) $9.60

Head Gasket Set - For Case tractor models 730 (Draft-O-Matic, s/n 8253500-later), 740 (Draft-O-Matic, s/n 8253500-later), Compatible with Case Combine (s) 800, Compatible with Case Construction and industrial models 680CK, Compatible with Case Engine (s) G251, Replaces Case OEM number A189525, A40899, A40341, Contains all gaskets necessary to replace the cylinder head (valve seals not included), (Item #: 106154) $166.00

Head Gasket Set - For tractor models Case 400 Super, 730, 740 Diesel, Case Industrial 680 Diesel, Case Industrial 680B Diesel, Case Industrial 750 Diesel all with A267D Diesel Engine. This gasket set does not fit applications for the A267D outside of those listed. (Item #: 106155, Ref: HS3273Y) $106.00

Oil Pan Gasket - For Case tractor models 400, 420, 700, 730 (s/n 8253500-earlier), 740 (s/n 8253500-later), 800, 830 (s/n 8253500-later), 840 (s/n 8253500-earlier), Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W9 (s/n 8150185-earlier), W9A, 425, 680B (s/n 9103966-earlier), 680CK, 750 (s/n 7070350-later), 850 (s/n 7073468-earlier), Compatible with Case Engine (s) D267, D301, G251, G284, Replaces Case OEM number A7616, Oil Pan Gasket Only, (Item #: 106167) $19.80

Oil Pan Gasket - For Case tractor models 400, 730, 740, 830, 840 (all gas and diesel with Case-O-Matic transmission), Replaces Case OEM number A189510, Engines: A267D, A301D, 215, (Item #: 107096) $28.50

Oil Pan Gasket Set - For Case tractor models 400, 730, 740, 830, 840 (gas and diesel using CK Draft-O-Matic transmission), Replaces Case OEM number A189516, Engines: A267D, A301D, 251, (Item #: 107097) $315.00

Rear Crankshaft Seal - For Case tractor models 730 (s/n 8253500-earlier), 740 (s/n 8253500-later), 770, 830 (s/n 8253500-earlier), 840 (s/n 8253500-earlier), 870, 930 (s/n 82583382-later), 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370, 1470, 1570, 2090, 2094, 2290 (engine s/n 10339530-later), 2294, 2390 (engine s/n 10339530-later), 2394, 2470, 2590 (engine s/n 10338578-later), 2594, 2670, 3294, 4490 (engine s/n 10338516-later), 4494, 4690, 4694, Compatible with Case Combine (s) 1010, 1060, Compatible with Case Construction and industrial models W7, W7E, W8B, W8C, W8E, W9A, W9B, W9C, W9E, W10 (s/n 8229366-earlier), W10B, W10C, W10E, W12, W14 (engine s/n 2571280-later), W14FL (s/n 9119671-later), W14H (s/n 9119671-later), W18, W18B, W20, W20B, W20C, W24, W24B (engine s/n 2572010-earlier), W24C, W26B, W30, W36, 35B, 40D, 40E, 50E, 300C, 400C, 475 (s/n 3058168-earlier), 600, 680B, 680C, 680CK, 680E, 680G, 680H, 750, 780B, 780CK, 800, 850 (s/n 7073468-later), 850B, 850C, 855C, 880, 880B, 880C, 980, 980B, 1080, 1080B, 1150 (s/n 7110299-later), 1150B, 1150C, 1150D, 1155D, 1280, 1280B, 1450, 1450B (engine s/n 10335336-later), 1455B (engine s/n 10335336-later), Compatible with Case Engine (s) D267, D301, D401, D451, G251, G284, 267BD, 301BD, 336BD, 336BDT, 401BD, 401BDT, 451BD, 451BDT, 504BD, 504BDT, 504BDTI Replaces Case OEM number A62050, A23085, A62700, , Compatible with Case IH tractor models 3394, 3594, (Item #: 106147) $29.30

Rear Crankshaft Wear Sleeve - For Case tractor models 730 (s/n 8253500-earlier), 740 (s/n 8253500-later), 770, 830 (s/n 8253500-earlier), 840 (s/n 8253500-earlier), 870, 930 (s/n 82583382-later), 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370, 1470, 1570, 2090, 2094, 2290 (engine s/n 10339530-later), 2294, 2390 (engine s/n 10339530-later), 2394, 2470, 2590 (engine s/n 10338578-later), 2594, 2670, 3294, 4490 (engine s/n 10338516-later), 4494, 4690, 4694, Compatible with Case Combine (s) 1010, 1060, (Item #: 106148) $147.00

Engine Rebuild Kits

Engine Rebuild Kit - Less Bearings, D267 - For Case tractor models 400 (Super), 730, 740, Compatible with Case Engine (s) D267, Flat top piston, 1.358" piston pin diameter, Kit includes: Pistons, Piston Ring Set, Liners, Connecting Rod Bushings, and Gasket set with Crank Seals, Kit does not include connecting rod or main bearings, For .156" Thrust Washer Set use Item #: 106127, (Item #: 130546) $1419.01

Engine Parts

Exhaust Valve - For Case tractor models 400, 420, 600, 700, 730, 740, 800, 900, 930, 940, Compatible with Case Combine (s) 800, Compatible with Case Construction and industrial models W8B, W8C, W9, W9B, W9C, W10B, W10C, 425, 680CK, Replaces Case OEM number A33423, A33456, A21711, 1.545" Head Diameter, Length: 6.540", (Item #: 128712) $33.20

Piston Pin Bushing - For Case tractor models 400, 420, 500, 600, 700, 730, 740, 770, 800, 830, 840, 870, 900, 920, 930, Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W7E, W8B, W8C, W8E, W9, W9A, W9B, W9C, W9E, W10, W10B, W10C, W10E, 680CK, Compatible with Case Engine (s) D267, D401, G251, G284, G301, G377, Replaces Case OEM number A27846, 1.358" pin, (Item #: 108142) $47.30

Valve Guide - For Case tractor models 730, 740, 770, 830, 840, 870, 930, 940, 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370, 1470, 1570, 2090, 2094, 2290, 2294, 2390, 2394, 2470, 2590, 2594, 2670, 3294, 4490, 4494, 4690, 4694, Compatible with Case Construction and industrial models W7, W7C, W7E, W8, W8B, W8C, W8E, W9, W9B, W9C, W9E, W10, W10B, W10C, W10E, W12, W14, W18, W18B, W20, W20B, W20C, W24B, W24C, W26, W26B, W30, W36, 35D, 40, 40D, 40E, 45, 45B, 50, 50D, 50E, 475, 680, 680B, 680C, 680E, 680G, 680H, 750, 780B, 850, 850B, 850C, 855C, 880, 880B, 880C, 880R, 980, 980B, 1080, 1080B, 1150, 1150B, 1150C, 1150D, 1155D, 1280, 1280B, 1285, 1450, 1450B, Compatible with Case Engine (s) 267BD, 301BD, 336BD, 336BDT, 401BD, 451BD, 451BDT, 504BD, 504BDT, 504BDTI, Replaces Case OEM number A41783, A41781, A21674, A11803, Exhaust, (Item #: 128713) $6.20

Valve Keeper - For Case tractor models 400 (Super, s/n 8106131-later), 730, 740, 830, 840, 870, 930, 940, 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370, 1470, 1570, 2090, 2094, 2290, 2294, 2390, 2394, 2470, 2590, 2594, 2670, 3294, 4490, 4494, 4690, 4694, Compatible with Case Combine (s) 1060, Compatible with Case Construction and industrial models W7, W7C, W7E, W8B, W8C, W8E, W9A, W9B, W9C, W9E, W10B, W10C, W10E, W12, W14, W18, W18B, W20, W20B, W20C, W24, W24B, W24C, W26B, W30, W36, 35D, 40, 40D, 40E, 45, 45B, 50D, 50E, 475, 680, 680B, 680C, 680E, 680G, 680H, 750 (s/n 7070351-earlier), 780, 780B, 850 (s/n 7073469-earlier), 850B, 850C, 855C, 880, 880B, 880C, 880R, 980, 980B, 1080, 1080B, 1150, 1150B, 1150C, 1150D, 1155D, 1280, 1280B, 1285, 1450, 1450B, Compatible with Case Engine (s) D267, D267B, D301, D301B, D401, D451, 336BD, 336BDT, 451BD, 451BDT, 504BD, 504BDT, 504BDTI, Replaces Case OEM number A27872, Sold per 1/2 valve, order 2 per valve, (Item #: 128514) $3.60

Valve Lifter - For Case tractor models 730 (s/n 8253500-earlier), 740 (Draft-O-Matic, s/n 8253500-later), 770, 830 (Draft-O-Matic, s/n 8253500-later), 840 (Case-O-Matic, s/n 8253500-earlier), 870, 930 (s/n 8258382-later), 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370 (late or upgraded), 1470 (late or upgraded), 1570, 2090, 2094, 2290 (engine s/n 10339530-later), 2294, 2390 (engine s/n 10339530-earlier), 2394, 2470 (late or upgraded), 2590 (engine s/n 10338578-earlier), 2594, 2670 (late or upgraded), 3294, 4490 (engine s/n 10338516-earlier), 4494, 4690, 4694, Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W7E, W8B, W8C, W8E, W9A, W9B, W9C, W9E, W10 (s/n 8229366-earlier), W10B, W10C, W10E, W12, W14 (engine s/n 2571280-later), W14FL (s/n 9119671-later), W14H (s/n 9119671-later), W18, W18B, W20, W20B, W20C, W24 (early), W24B (engine s/n 2572010-later), W24C (early), W26B, W30, W36 (s/n 17753999-earlier), 35B (with turbo), 40D, 40E, 50E, 300C (late), 400C (late), 475 (s/n 3058168-later), 600 (late), 680B (s/n 9103966-earlier), 680C, 680CK, 680E (early), 680G (early), 680H, 750 (s/n 7070350-later), 780B (late with engine balancer), 780CK (early with turbo), 800 (early), 850 (s/n 7073468-earlier), 850B (early), 850C, 855C, 880 (early), 880B (early), 880C, 980, 980B, 1080, 1080B, 1150 (s/n 7110299-earlier), 1150B, 1150C, 1150D, 1155D, 1280, 1280B, 1450 (late), 1450B (engine s/n 10335336-earlier), 1455B (engine s/n 10335336-earlier), Compatible with Case Engine (s) D267, D267B, D301, D401, D451, G251, G284, G301, G377, 301BD, 336BD, 336BDT, 401BD, 401BDT, 451BD, 451BDT, 504BD, 504BDT, 504BDTI, Replaces Case OEM number A182179, A21857, Sold individually, (Item #: 160901) $22.80

Valve Rotator - For Case tractor models 420, 600, 700, 730, 740, 770, 800, 830, 840, 870, 900, 930, 970, 1030, 1070, 1090, 1170, 1175, 1200, 1270, 1370, 1470, 1570, 2090, 2094, 2290, 2294, 2390, 2394, 2470, 2590, 2670, 3294, 4490, 4494, 4690, 4694, Compatible with Case Combine (s) 800, 1010, 1060, Compatible with Case Construction and industrial models W7, W7E, W8B, W8C, W8E, W9, W9A, W9B, W9C, W9E, W10, W10B, W10C, W10E, W12, W14, W14FL, W14H, W18, W18B, W20, W20B, W20C, W24, W24B, W24C, W26B, W30, W36, 35B, 40D, 40E, 50E, 300C, 400C, 600, 680B, 680C, 680CK, 680E, 680G, 680H, 750, 780B, 780CK, 850, 850B, 850C, 855C, 880, 880B, 880C, 980, 980B, 1080, 1080B, 1150, 1150B, 1150C, 1150D, 1155D, 1280, 1280B, 1450, 1450B, 1455B, Compatible with Case Engine (s) 301BD, 336BD, 336BDT, 451BDT, 504BD, 504BDT Replaces Case OEM number A23061, A66336, A44658, A24993, O10735AB, O21687, , Compatible with Case IH tractor models 2594, (Item #: 168538) $19.00

Engine Pistons and Sleeves

No
Picture
Piston and Sleeve Kit, Overbore - Sleeve and piston kit, overbore from 4-1/8" to 4-1/4", complete for 4 cylinders. Contains sleeves, pistons, rings, pins, and retainers. 1 kit used in A267D 4 cylinder diesel engine. 4 cylinder Case Super 400 diesel, 8106131/up, 700 diesel, 730 diesel, 740 diesel, 800B diesel engine A267D. (Item #: PK253) $761.93

No
Picture
Sleeve and Piston Kit - This sleeve and piston kits is for 4 1/4 Overbore with 1.358 Pin Diameter. Includes sleeve, pistons, piston rings, piston pins and piston pin retainers. For 400 Super, 680CK, 700, 730, 740, 800 with A267D Diesel Engine (Item #: R3322) $678.56

Engine Rings

No
Picture
Piston Ring Set, 4 Inch Bore - 12 compression rings 3/32 inch, 4 oil rings 1/4 inch. For tractor models C, CC, CI, CO, D, DC, DI, DO, 400, 420, 680CK, 700, 730, 740, 770, 800, 810. Not for use with chrome sleeve liners. (Item #: 130066, Ref: 1486638) $138.00

Piston Ring Set - Standard - Single Cylinder - For Case tractor models 400, 500, 600, 700, 730, 740, 770, 800, 900, 920, 930, 970, Compatible with Case Combine (s) 800, Compatible with Case Construction and industrial models W8B, W8C, W8E, W9, W9B, W9C, W9E, W10B, W10C, W10E, 420, 425, 680CK, Compatible with Case Engine (s) D251, D377, G251, G260, G377, Replaces Case OEM number A46308, Bore: 4.000", Ring Size: Standard, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (1) @ .250", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .250", 4th Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For 6 Cylinder Piston Ring Set use Item #: 174201, (Item #: 120737) $28.30

Exhaust System

Exhaust Manifold Ferrule - This is a tapered Exhaust Manifold Ferrule. It tapers from 1.885 inches to 1.752 inches outside diameter, 1.625 to 1.743 inches inside diameter. It is 0.493 inches wide. Used on (730, 740, 741, 742, 743, 744 gas, 4 used), (930 Early, gas, up to Engine SN: 2142562 (1964) with center exhaust, 6 used) 680; Replaces: A21635 (Item #: 167999, Ref: A21635) $14.40

Exhaust Manifold Gasket - This Exhaust Manifold Gasket measures 2.506 inches outside diameter, 1.786 inches inside diameter and is 0.085 inches thick. It fits: (L, LA, LAH, LAI, LAIH, LAIM, LI all gas, distillate, 2 used for INTAKE only), (Super 400, 400, 401, 402, 403, 405, 410, 411, 412, 413, 414, 415, 425 all gas, LP, diesel, 4 used), (500, 520 both diesel, 6 used), (610, 620 both LP, diesel; 6 used), (700, 710, 710B, 711, 712, 712B, 713, 713B, 715, 715B, 725B, 730, 740, 741, 742, 743, 744, 810, 810B, 811, 811B, 812, 812B, 813, 813B, 815 gas, 4 used), (900, 900B, 910, 910B, 920B gas, LP, diesel; 6 used), (930 Early 1960 - 64, gas with center exhaust, 6 used), (940, 941 1960 - 64, gas with center exhaust, 6 used)], (711B gas, 4 used), (420 gas, LP, diesel. 4 used), (600 LP, diesel; 6 used), (800 gas, 4 used), 680CK, (W9 gas, 4 used). Replaces: 1349071C1, A27909, O1437AB, O9815AB (Item #: 180167, Ref: A27909) $6.70

Intake Manifold Gasket - Fits: (400, 410, 411, 412, 413, 414, 415, 700, 710, 710B, 711, 711B, 712, 712B, 713, 713B, 715, 715B, 725B, 730, 740, 741, 742, 743, 744, 810, 810B, 811, 811B, 812, 812B, 813, 813B, 815, 815B (gas, LP; 2 used)), (610, 900, 910 (LP, 3 used)), 930 (Early, 1960 - 64, gas, LP with center exhaust, 3 used), (940, 941 (1960 - 64, gas, LP with center exhaust, 3 used)); Case Industrial - Fits: 600 Skidder (LP, 3 used), 800 Skidder (gas, LP; 2 used), (680CK, W9 (gas, 2 used)) Replaces: 1349068C1, A7363 (Item #: 185141, Ref: A7363) $6.57

Manifold - Gas Exhaust manifold For Fits: 700, 710, 710B, 711, 711B, 712, 712B, 713, 713B, 715, 715B, 725B, 800, 810, 810B, 811, 811B, 812, 812B, 813, 813B, 815, 815B, 730, 730CK, 730 Comfort King, 730 Draft-O-Matic, 740, 741, 742, 743, 744, 830, 830 Comfort King, 830 Draft-O-Matic, 840, 841, 842, 843; Replaces original part numbers A11250 and A20867. NOTE: The outlet outside diameter is 2-1/2". Many tractors on this list have an original 2-1/4" outlet manifold. You may need to change muffler if the outlet is different than the manifold you are replacing. If new Ferrules are needed, see part numbers A11837 and A21635. If Gaskets are needed, see part numbers A11889 and A27909 (Item #: 101505, Ref: R4068) $353.87

Muffler - Vertical Exhaust Inlet inside 2 1/2 inch, outlet outside diameter 2 1/2 inch, overall length 26 inches. For 730, 740, 830, 840 Gas and Diesel. OEM number use MC212 clamp, use R1802 rain cap. (Item #: 100272, Ref: R1054) $60.54

Fuel System / Air Intake

Air Cleaner Bowl - Clear plastic pre-cleaner bowl for the air intake system. Bowl outside diameter at top approximately 7-1/4 inch, side height 3 inches, cone inside diameter at top 3-1/2 inch, overall height 4-1/8 inch. Commonly used on pipe inlets ranging from 2-3 inches. For the following 430 diesel, 530, 730, 930, 470 diesel, 570, 770, 830, 870, 1030CK, 1031, 1032, 580B, 431 diesel, 531, 631, 632, 740, 741, 742, 744, 840, 841. Can replace Donaldson P02-0227, also replaces 101965A, 10P871, 1125804, 1508881M1, 3119347, 365413R1, 71125804, 73186, 73533, 80073533, C0NN9A663A, F3446R, L60631, R28794 (Item #: 157279, Ref: R28794) $8.80

Cable Clip for Marvel Schebler Carburetors - Many Marvel Schelber Carburetors use one of these clips to secure the choke or the fuel cable. On Case it is used For: [V, VA, VAC, VAI, VAIW, VAO, VAO-15, VAS, VC, VI, VO, 200B, 210B, 211B, 300B, 301B, 310B, 311, 311B, 312, 312B, 320B, 350, 351, 400B, 410B, 411B, 420B, 430, 440, 441, 445, 470, 530, 540, 541, 545, 570, 600B, 610B, 611B, 614B, 630, 632, 634, 640, 641, 642, 644, 730, 740, 741, 742, 743, 744, 830, 840, 841, 842, 843 (For choke cable bracket with Marvel Schebler carb # TSX42, TSX43, TSX74, TSX114, TSX212, TSX225, TSX253, TSX409, TSX474, TSX635, TSX710, TSX717, TSX749, TSX762, TSX785, TSX794, TSX798, TSX799, TSX804, TSX854, TSX936, TSX957SL, TSXU838) ], [310, 310B, 310C, 310D, 310E, 310F, 310G, 680CK, W5, W7, W9A (For choke cable bracket) ], Industrial; Skid steer: 1737 (For choke cable bracket); Replaces: 29-81, B51765 (Item #: 126116, Ref: CT29-81) $5.10

Carburetor - New carburetor with reversible linkage. Fits 700, 740, 840 with 284 engine, 800 and 1000 combines. Replaces numbers TSX394, TSX777, TSX782, TSX785, TSX863, TSXU839, TSXU995. Center to center on the 2 mounting bolts is 2 11/16 inches. (Item #: 100750, Ref: 14997) $533.00

Carburetor Float - Zenith Carburetor Float Use w/ Zenith Carburetors: 11535, 11537, 11580, 11588, 11705, 11973, 12032, 12066, 12217, 12232, 12590, 12293, 12427, 12471, 12509, 12534, 12548, 12685, 12758, 12902, 12913, 12994, 13048, 13106, 13107, 13108, 13109, 13151, 13153, 13154, 13161, 13294, 13304, 13316, 13318, 13328, 13338, 13337, 13338, 13372, 13374, 13378, 13384, 13390, 13406, 13416, 13465, 13546, 13578, 13588, 13596, 13608, 13612, 13628, 13716, 13758, 13783, 13795, 13808, 13875, 13881, 13912, 13913, 13914, 13915, 13916, 13917, 13920, 13956, 14991, 14992, 14995, 14996, 14997, 14999. Replaces E1NN9550AA, 1508089M91, B51359, 70227103, 381027R1, 1K7630. (Item #: 108448, Ref: R4531) $24.40

Carburetor Float - Use with Marvel Schebler Carbs: TSX11, TSX616, TSX749, TSX780, TSX782, TSX785, TSX794, TSX863 For MODELS: D Series, 400, 410B, 511B, 730, 740, 840 (Item #: 108451, Ref: R4012) $31.70

Carburetor Kit, Basic - Kit for Marvel TSX616, TSX780, TSX749, TSX782, TSX794, TSX785, TSX863, TSX11 carbs used on 400, 410B, 511B, 6799, 8714, 730, 740, 840, D, DC, DC-3, DC-4, DH, DI, DO, DS, DV, L, LA, LA1, LA1H, LAD, LAE. (Item #: 100735, Ref: MS103) $23.50

Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: TSX785. For the following tractor models: 730, 740, 830, 840. Add $100.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203250, Ref: 1228-CARB) $324.01

Carburetor, Rebuilt - This rebuilt carburetor is a direct replacement for OEM numbers matching: TSX863. For the following tractor models: 730, 740, 830, 840. Add $100.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203251, Ref: 1229-CARB) $550.01

Needle Valve - Viton Float Valve Needle, Seat and Gasket Assembly for some Marvel Schebler carburetors. For the following models: D (specific for TSX11), 400, 540, 630, 634, 640, 641, 642, 644, 700, 740, 741, 742, 744, 830, 840, 841. Replaces 233-543 and B51914. (Item #: 179751, Ref: C3NN9D532A) $7.00

Sediment Bowl Assembly - Large Bowl. 1/8 inch pipe thread to fuel line, 3/8 pipe to tank. Fuel Strainer assembly with 2.25 inch bowl. For the following models using the large bowl: CC, CI, CO, L, LA, LAI, LI, R, RC, 400, 700, 730, 740, 741, 742, 744, 830, 840, 841. Replacement bowl available as part S.65504. Replaces A22615 and O1933AB. (Item #: 105393, Ref: S.61581) $22.00

Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: A11211, T7040 (Item #: 105364, Ref: 49923D) $3.50

Lights

Bulb, Sealed Beam, Flood - 12-Volt Hi-Beam with Double Contact. It is 35 Watt with a 4.4 Inch Outside Diameter. It is Interchangeable with original lamp 4406 and 4410. Check lamp number before ordering. Replaces: 4410, A42294, A43639, A47179, D33182, L30464 (Item #: 111242, Ref: 28A116) $12.90

LED Lamp, 12 Volt - This LED Floodlight is for 12-volt Negative Ground Systems only. It is polarity specific. It is a direct replacement for 4410, 4411 sealed beam or halogen. Features 6-LED, 1440 Lumens, 18 Watts. 4-1/2 Inch diameter. The flood beam is an excellent work light that illuminates wide and short areas. Replaces 239804, 1164605, 70239804, 71164605, 4410, A42294, A43639, A47179, D33182, L30464, 105774A, 30-3169898, 209495, 251534, C0NN15330A, C5NN13007F, E3NN15330AA, 126470C1, 131203C1, 131348C1, 131508C1, 390756R91, AE31263, AR104119, AR21059, AT25451, H7606, RE285628, RE336111, RE35168, RE561116, 285871M1, 505281M1, 509652M91, 10P2645, 105774A, 166407A, 30-3169898, 735606A (Item #: 127096, Ref: L4411LED) $35.00

Light Bulb, Sealed Beam, 12 Volt - This 12-Volt Sealed Beam has Double Contact. It is 35 Watt. Has a 4.365 inch outside diameter. Replaces: L4411, 4411, A24572, A40855, A42295, D71409, E98744, K962145. (Item #: 111241, Ref: 373662R91) $9.10

Light Ring - The dimensions of this light ring with screw are 4.5 inches in height and 0.885 inches in width. Replaces 10P1552, 230233, 371445R91, 371449R91, 371451R91, 70230233, AF3891R, B50255, B50258, JDS676. Verify measurements before ordering. Most models used more than one headlight style in production. (Item #: 154743, Ref: 371449R91) $25.70

$Case 740 Tail Light \ Dash Light Bulb - 12-Volt$
Tail Light / Dash Light Bulb - 12-Volt - This 12 Volt Bulb is a Single contact with a Bayonet base. It is 0.59 amps. The base diameter is 0.595 inches. It is used in many tail lights and dash lights. May be used when changing from 6 to 12 Volts. Replaces: B50223 (Item #: 150699, Ref: TLBULB12V) $1.70

Seats

Seat Back - Black Vinyl on Steel For 430, 440, 470, 530, 540, 570, 580, 630, 730, 740, 830, 930, 940, 1030. Replaces A24712-1, A24712 (Item #: 127413, Ref: R4363) $158.00

No
Picture
Seat Back - Black Vinyl on Wood For 730, 740, 830, 840, 930, 940, 1030, 1070, 1175 Comfort King (Item #: 101206, Ref: R1169) $159.91

Seat Bottom - Black Vinyl on Steel For 430, 440, 470, 530, 540, 570, 580, 630, 730, 740, 830, 930, 940, 1030. Replaces A24713 (Item #: 127412, Ref: R4362) $123.00

No
Picture
Seat Bottom - Black Vinyl on Wood. For tractor models 730, 740, 830, 840, 930, 940, 1030, 1070, 1175 Comfort King. (Item #: 101205, Ref: R1168) $114.64

Steering

Steering Shaft Cross and Bearing (U-Joint) - Tighten up your steering with a new Universal Joint. This part measures 2.305 inches across cap to cap, with a 0.968 inch cap diameter. Some steering systems use more than one joint. Sold individually. Replaces OEM numbers 10P715, 1KAR758, 224890, 350254R91, 357439R91, 363313R91, 363321R91, 52977DAX, 70224890, 836514M91, 841193M92, A20435, A20684, A30408, A30425, A30428, A30435, VTA3227, Z862, VTA3127 (Item #: 115351, Ref: 70224890) $11.00

Steering Wheel Nut - This steering wheel nut fits the following tractor models: D, DC, DC3, DC4, DCS, DEX, DH, DI, DO, DV, L, LA, S, SC, SI, SO, V, VA, VAC, VAE, VAH, VAI, VAO, VAS, VC, VI, VO, 1030, 1030CK, 930, 1031, 1032, 200, 200B, 210, 210B, 211B, 300, 300B, 310, 310B, 320, 320B, 400B, 410B, 420B, 430, 430CK, 440, 470, 530, 530CK, 540, 570, 500, 520, 600, 610, 620, 630, 640, 730, 830, 730CK, 740, 830CK, 840, 900, 930CK, 931, and 932. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 4291112, 352536R1, 25-1512 and 251512. (Item #: 157780, Ref: 353435X1) $1.00

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: G45291, G57046 (Item #: 103768, Ref: FW60166) $92.00

Stop Body Screw, Single - This stop body screw for the rear wheel rim is used with power adjust rims 535453M91, 535452M91, PAR10X28, C5NN1050J and C5NN1050H. Replaces: A9440, G15442, K200142. YOU MAY RECEIVE A HEX HEAD OR SQUARE HEAD. (Item #: 155118, Ref: C0NN1058A) $6.60

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems

Decal - Case Eagle Decal, 2 inch. (Item #: 100513, Ref: R5170) $2.70

Decal - Case Eagle Decal, 1-1/4 inch printed on vinyl. (Item #: 183056, Ref: R5235) $2.60

Decal - Case Eagle Decal, 4 inch. (Item #: 100524, Ref: R1299) $5.30

Decal - Case Eagle Decal, 6 inch. (Item #: 100525, Ref: R1300) $7.00

Decal - Case Eagle Decal, 9 1/2 inch. (Item #: 100526, Ref: R1303) $8.80

Draft-O-Matic Decals - Draft-O-Matic Decals, Round (Set of 2) - Vinyl Cut. Decal is used in association with any other listed decal set if you have a DRAFT-O-MATIC. (Item #: 100517, Ref: R2247) $26.20

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style.. (Item #: 178026, Ref: ADR9209) $14.40

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Battery Thermal Wrap - This thermal battery wrap is used to keep your battery warm. It is 60 Watts and measures 28 inches long. (Item #: BTW28) $22.50

No
Picture
Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20

Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80

No
Picture
Spark Plug - Standard tip, 14mm thread, 3/8" reach. Replaces Champion J17LM, Motorcraft A7CLM. NOTE: Verify spark plug type before ordering. (Item #: AL456) $2.40

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80

$Case 740 Tag for Starter\Generator, 12 Volt, Blank$
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Case 740 Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10

$Case 740 Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Case 740 Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90

$Case 740 Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30

$Case 740 Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40

$Case 740 Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70

Rain Cap - Rain Caps are located in the EXHAUST category of the Accessories and Universal parts section.

NOTE

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.00

Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $12.90

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40

Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00

Carburetor Elbow and Strainer - Fits some Case models. VERIFY FITTING MEASUREMENTS. Fits some Carter UT Series carburetors. Used with flair fitting, not compression fitting. Male end (screen end) is 1/8 inch pipe threads. Female end is 1/4 inch flair. (Item #: 110005, Ref: 9N9553) $5.50

Carburetor Float, Zenith - This Float is used in the following Zenith Carburetors: 10277, 12188, 12199, 12205, 12234, 12236, 12238, 12253, 12384, 12389, 12535, 12599, 12654, 12744, 12956, 12982, 13096, 13201, 13206, 13238, 13309, 13355, 13371, 13386, 13405, 13415, 13420, 13452, 13453, 13492, 13549, 13605, 13646, 13653, 13665, 13694, 13705, 13713, 13719, 13720, 13727, 13729, 13730, 13733, 13800, 13803, 13805, 13822, 13825, 13851, 13861, 13862, 13865, 13873, 13878, 13879, 13880, 13902, 13903, 13910, 13933, 13957, 13971, 13975, 13983, 14002, 14017, 14019, 14044, 14086, 14094, 14096, 14099, 14100, 14115, 14133, 14147, 14175, 14178, 14179, 14183, 14993 (Item #: 108454, Ref: C85-103-S) $17.00

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92

$Case 740 Sediment Bowl Gasket, 2-1\8 inch$
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar

Eagle Hitch Leveling Knob, Rubber - For all models using Eagle Hitch. Replaces O4995AB. (Item #: 126108, Ref: A26845) $15.20

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.40

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60

No
Picture
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50

Universal Pressure Gauge, Hydraulic - 160 lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglas crystal. 1/4 NPT male brass fitting. (Item #: GG160) $9.96

Universal Pressure Gauge, Hydraulic - 100 LB Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: GG100) $9.96

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13

Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50

No
Picture
Paint, Case Yellow, Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 154618, Ref: TP160GAL) $100.00

No
Picture
Paint, Case Yellow, Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 154616, Ref: TP160QT) $42.80

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00

No
Picture
Paint, Clear Coat, 1 Quart - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00

No
Picture
Paint, Desert Sand, 1 Gallon - This Case Desert Sand color is SPECIAL ORDER - NON RETURNABLE. Ensure you have correct color. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108139, Ref: TP130GAL) $105.00

No
Picture
Paint, Desert Sand, 1 Quart - This Case Desert Sand color is SPECIAL ORDER - NON RETURNABLE. Ensure you have correct color. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108138, Ref: TP130QT) $38.10

No
Picture
Paint, Desert Sand, Spray Can - This Case Desert Sand color is SPECIAL ORDER - NON RETURNABLE. Ensure you have correct color. Ensure you have correct color. From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108137, Ref: TP130SP) $10.30

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.30

No
Picture
Paint, Power White, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100348, Ref: TP271GAL) $61.00

No
Picture
Paint, Power White, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100347, Ref: TP271QT) $24.00

No
Picture
Paint, Power White, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100346, Ref: TP271SP) $9.80

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $100.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $173.00

Steering

Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $417.87

Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: A22279, A30834, A42242, G45307, K964615, O10582AB, K902187, K960750 (Item #: 111126, Ref: AE33538A) $13.20

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $47.60

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $23.10

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $287.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $78.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.00

Tire, Three Rib - Front tire, 3 Rib, 5.50 inches x 16 inches. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $107.00

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $19.10

No
Picture
Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $57.00

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $111.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $67.00

No
Picture
Tire Tube 38 Inch - This 38 inch tire tube is used for all tractors with the following tires: 10.00 inch x 38 inch, 11.00 inch x 38 inch, 11.2 inch x 38 inch and 12.4 inch x 38 inch. This is a bias style tube, not for radial tires. (Item #: 183819, Ref: WHS064) $82.00